3176C, 3406E and 3456 Industrial Engines Caterpillar


Coolant Level Is Low

Usage:

3196 1DW
使用本步骤诊断和排除冷却液液位低故障,或者在下列任一事件代码为现行状态时使用本步骤。 有关事件代码和这些代码的默认触发点的信息,请参阅 故障诊断与排除, "事件代码列表"。 必须进入 Caterpillar 电子技师(ET)的监控系统才能查看这些代码的当前触发点。

表 1
事件或诊断代码    
代码和描述     产生此代码的状况     系统响应    
E058(3)发动机冷却液液位低停机     发动机冷却液液位降至冷却液液位传感器以下已达到规定的延迟时间。     记录该代码。
发动机将在 10 秒后停机。    
E059(1)发动机冷却液液位低警告     发动机冷却液液位降至冷却液液位传感器以下已达到规定的延迟时间。     记录该代码。    
111-1 冷却液液位低警告     发动机冷却液液位降至冷却液液位传感器以下已达到规定的延迟时间。     记录该代码。
诊断灯将闪烁。
报警灯将发光。    
111-11 冷却液液位极低(减额)     发动机冷却液液位降至冷却液液位传感器以下已达到规定的延迟时间。     记录该代码。
诊断灯将闪烁。
报警灯将闪烁。
发动机将在"警告"后的 10 秒减额。    
111-11 冷却液液位极低(停机)     发动机冷却液液位降至冷却液液位传感器以下已达到规定的延迟时间。     记录该代码。
发动机将在 30 秒后停机。    

可能原因

  • 冷却液液位低和/或冷却液泄漏

  • 冷却液液位传感器

建议的措施

冷却液液位低和/或冷却液泄漏

    ------ WARNING! ------

    热的冷却液、蒸汽和碱会造成人身伤害。

    在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。

    只有当发动机停机且散热器盖已经冷却到可以徒手触摸时,再慢慢拆下过滤器盖以释放压力。

    冷却系统调节器含碱。 应避免它与皮肤和眼睛接触。


  1. 检查冷却液液位。 如有需要,添加冷却液。

  1. 检查防冻液和水的混合是否正确。 请参阅操作和保养手册。

  1. 检查冷却系统有无泄漏。 立即修理所有泄漏。

  1. 检查冷却系统中有无空气。 请参考系统操作/测试和调整以了解正确步骤。

冷却液液位传感器

如果怀疑冷却液液位传感器存在电气故障,请参考故障诊断与排除, "冷却液液位 - 测试"以了解关于对冷却液液位传感器的电气故障进行故障诊断与排除的信息。

Caterpillar Information System:

3176C, 3406E and 3456 Industrial Engines Coolant Contains Oil
C3.3 Industrial Engine Fuel System - Prime
Product Link PL321 De-registration{7606} Product Link PL321 De-registration{7606}
C18 Petroleum Generator Sets Model View Illustrations
C15 and C18 Petroleum Generator Sets Model View Illustrations
C-15, C-16, and C-18 Truck Engines Belt Tensioner
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
3608 Engine Fuel Transfer Pump - Disassemble
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
3608 Engine Prelubrication Oil Pump - Assemble
C27 and C32 Industrial and Petroleum Engines Exhaust Manifold
Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490} Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}
2008/01/21 Improved Canister for the Filter Housing {3004, 3067, 5068, 5091, 5092, 5093}
3176C, 3406E and 3456 Industrial Engines Coolant Temperature Is High
C15 and C18 Petroleum Engines Turbocharger Oil Lines
C15 and C18 Petroleum Engines Turbocharger Oil Lines
2007/11/01 Replacement of the Combustion Head for the Aftertreatment Regeneration Device in On-highway Engines {1088, 1720, 1722}
3608 Engine Valve Lifter - Assemble
C15 and C18 Petroleum Engines Turbocharger Oil Lines
Procedure to Relocate the Inlet Hose for the ARD Purge Air Pump{107P, 1803} Procedure to Relocate the Inlet Hose for the ARD Purge Air Pump{107P, 1803}
G3520C and G3520E Engines Turbocharger
Procedure for Using the Automatic Flash Update Tool for a UPS System{4480, 7620} Procedure for Using the Automatic Flash Update Tool for a UPS System{4480, 7620}
Manual Programming of a UPS System{4480, 7620} Manual Programming of a UPS System{4480, 7620}
G3500B Engines Nitrogen Oxide Sensor - Calibrate
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.