Hydraulic System Oil Filter - Replace
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Note: The Hystat transmission and the hydraulic system use a common tank.
- The hydraulic filter is located on the right side of the machine. Open the access door on the right side of the machine.
Show/hide table
Illustration 2 g03804358 Some components are removed for clarity - Remove the hydraulic filter element by using the following steps.
- Place a pan under the filter.
- Remove the drain plug. Then, loosen the filter housing with a strap type wrench to allow air entry into the filter housing to allow for oil drainage.
- Allow some time for complete drainage of oil from the filter housing.
- Remove the filter housing from the oil filter base.
- Clean the filter element mounting base. Remove any part of the filter element gasket that remains on the filter element mounting base.
- Replace a new filter element into the housing. Apply a light coat of oil to the gasket of the new filter element.
- Install the filter housing onto the filter base. When the gasket contacts the filter element mounting base, tighten the housing to a torque of
40 ± 5 N·m (30 ± 4 lb ft) . Use a32 mm (1.25 inch) box end wrench. - Install the drain plug. Tighten to a torque of
12.5 ± 2.5 N·m (9.2 ± 1.8 lb ft)
Show/hide tableIllustration 3 g03803970 - Maintain the hydraulic oil level so the oil is visible in the sight gauge . Add oil, if necessary.
Reference: See Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for additional information.
- Inspect the gasket on the cap for damage. Replace the gasket, if necessary.
Show/hide table
Illustration 4 g03803895 - Install the cap.
- Close the access door.
Show/hide table
Illustration 1 | g06206866 |
Caterpillar Information System:
New Object Detection and Secondary Display Retrofit Kits are Now Available for Certain Medium Wheel Loaders {1408, 1439, 7338, 7347, 7348, 7490, 7610, 7620} New Object Detection and Secondary Display Retrofit Kits are Now Available for Certain Medium Wheel Loaders {1408, 1439, 7338, 7347, 7348, 7490, 7610, 7620}
A New NOx Reduction System Cooler Group and Water Lines Group Are Now Used on Certain C15 / C18 Tier 4 Final Machine Engines {1061, 1087, 108C, 1380} A New NOx Reduction System Cooler Group and Water Lines Group Are Now Used on Certain C15 / C18 Tier 4 Final Machine Engines {1061, 1087, 108C, 1380}
A New NOx Reduction System Cooler Group and Water Lines Group Is Now Used on Certain C15 / C18 Tier 4 Final Machine Engines {1061, 1087, 108C, 108G, 1380} A New NOx Reduction System Cooler Group and Water Lines Group Is Now Used on Certain C15 / C18 Tier 4 Final Machine Engines {1061, 1087, 108C, 108G, 1380}
992K Wheel Loader General Information (Brake System)
D6K2 Track-Type Tractor Machine Systems Hydraulic Tank - Disassemble
D6K Track-Type Tractor Fuel Tank Water and Sediment - Drain
992K Wheel Loader Location of Components (Power Train System)
D6K Track-Type Tractor Fuel Tank Cap Filter and Strainer - Replace/Clean
D6K Track-Type Tractor Fuel System - Fill
D6K Track-Type Tractor Equalizer Bar Center Pin - Lubricate
Installation of the 530-2463 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133} Installation of the 530-2463 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133}
992K Wheel Loader Electronic Control (Power Train System)
994K Wheel Loader Systems Water Lines
D6K Track-Type Tractor Pivot Shaft Oil Level - Check
D6K Track-Type Tractor Radiator Pressure Cap - Clean/Replace
992G Wheel Loader Machine Systems Bucket - Remove
C11 and C13 Industrial Engines Engine Valve Lash - Inspect/Adjust
992K Wheel Loader Modulating Valve (Torque Converter Impeller Clutch)
854K Wheel Dozer Service Brakes - Impeller Clutch Operation
C7.1 Engines Electrical Connectors
992K Wheel Loader Parking Brake - Interlock
992G Wheel Loader Machine Systems Bucket - Install
D6K Track-Type Tractor Track Roller Frame - Inspect
992K Wheel Loader Electronic Control (Brake System)