Air in Fuel - Test
Show/hide table
为避免人身伤害,使用加压空气时一定要佩戴眼和脸的防护面具。 |
Show/hide table
注意 |
---|
切勿使用超过 |
本步骤用来检查燃油中是否有空气。 本步骤也可帮助查找空气源。
Show/hide table
所需工具 | ||
---|---|---|
零件号 | 零件名称 | 数量 |
2P-8278 | 管组件 | 1 |
检查燃油系统中是否有泄漏。 确保燃油管接头正确拧紧。 检查燃油箱中的燃油油位。 空气可能会从位于燃油输油泵和燃油箱之间的吸油侧进入燃油系统
- 将 2P-8278 管组件 (目测表)安装到燃油回油管内。 尽可能将目测表安装在燃油管上至少
304.8 mm (12 inches) 长的直线段。 不要将目测表安装在以下会造成紊流的装置的附近。- 弯头
- 安全阀
- 单向阀
在发动机盘车时,观察油流。 查看燃油中有无气泡。 如果目测表中没有燃油,则向燃油系统注油。 发动机起动后,在不同的发动机转速下检查燃油中是否有空气。 尽可能在怀疑燃油中有空气的工况下运转发动机。
Show/hide table图 1 g01096678 2P-8278 管组件 (目测表)
(1) 直径大约为1.60 mm (0.063 inch) 的稳定成串小气泡是燃油中可以接受的空气量。
(2) 如果气泡之间的时间间隔为 2 到 3 秒,则直径大约为6.35 mm (0.250 inch) 的气泡也可接受。
(3) 燃油中气泡过多是不容许的。 - 如果发现回油管上的目测表内有过多空气的话,应在输油泵的进口处安装第二个目测表。 如果只有一个目测表的话,将目测表从回油管拆下,然后安装在输油泵的进口处。 在发动机盘车时,观察油流。 查看燃油中有无气泡。 发动机起动后,在不同的发动机转速下检查燃油中是否有空气。
如果在燃油输油泵进口处没发现有过多空气,则空气就是从燃油输油泵之后进入系统的。 继续执行 "调整步骤" 的步骤 3。
如果发现输油泵进口处有过多空气的话,则空气就是由燃油系统的吸油侧进来的。
- 将燃油箱加压至
35 kPa (5 psi) 。 不要使用超过55 kPa (8 psi) 的压力以免造成燃油箱损坏。 检查燃油箱和燃油输油泵之间的燃油管是否有泄漏。 修理发现的所有泄漏。 检查燃油压力以确保输油泵正常操作。 关于燃油压力检查的信息,请参阅测试与调整, "燃油压力"。 - 如果还没有找到空气来源,可拆开油箱供油管,将一个外部供油接到输油泵的进口。 如果这样做解决了问题,修理燃油箱或燃油箱中的竖管。
- 如果喷油器套筒已磨损或损坏,则燃烧气体就可能进入燃油系统。 同样,如果喷油器套筒上的 O 形密封圈磨损、缺失或损坏,燃烧气体也可能进入燃油系统。
Caterpillar Information System:
992K Wheel Loader Position Sensor (Lift Linkage) - Replace
992K Wheel Loader Piston Pump (Implement) Main Relief Valve Pressure - Test and Adjust
992K Wheel Loader Calibration Error Codes
Announcing a Serviceability Update for Track Roller Frames for Certain D8N and D8R Track-Type Tractors {4151} Announcing a Serviceability Update for Track Roller Frames for Certain D8N and D8R Track-Type Tractors {4151}
New Clamshell Hood Bracket Is Now Used on Certain 980K, 980M, and 982M Wheel Loaders {7251} New Clamshell Hood Bracket Is Now Used on Certain 980K, 980M, and 982M Wheel Loaders {7251}
992K Wheel Loader Calibrations (Cat ET)
994K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B} M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
525D, 535D, 545D and 555D Wheel Skidders Solenoid Valve - Test
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Editing Truck and Material Lists
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Lubrication System
Installation Instructions For The New Solid-State Main Power Relay On Certain D6T Track-Type Tractors {1422, 1426} Installation Instructions For The New Solid-State Main Power Relay On Certain D6T Track-Type Tractors {1422, 1426}
992K Wheel Loader Position Sensor (Tilt Linkage) - Replace
953K and 963K Track-Type Loaders Caterpillar Approved Work Tools
MD6310 Rotary Drill Belt - Inspect/Adjust/Replace
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
992K Wheel Loader Pilot Control Actuator Pressure - Check
D6T Track-Type Tractor Electrohydraulic System Diagnostic Capabilities
312D2 and 313D2 Excavators Plate Locations and Film Locations
Improved Viscous Cab Mount Is Now Used on Certain 980M and 982M Medium Wheel Loaders {7301, 7301} Improved Viscous Cab Mount Is Now Used on Certain 980M and 982M Medium Wheel Loaders {7301, 7301}
An Improved Latch Assembly in the Rear Guard Is Now Used on Certain D5R and D6N Track-Type Tractors {7187} An Improved Latch Assembly in the Rear Guard Is Now Used on Certain D5R and D6N Track-Type Tractors {7187}
New Secondary Steering Software Control Is Now Used on 980H Wheel Loaders {4300, 4324, 4800, 4808, 7610, 7620} New Secondary Steering Software Control Is Now Used on 980H Wheel Loaders {4300, 4324, 4800, 4808, 7610, 7620}
Installing The 523-4907 Work Tool Positioner Kit {5112, 5264, 5479} Installing The 523-4907 Work Tool Positioner Kit {5112, 5264, 5479}
Installing The 523-4908 Work Tool Positioner Kit {5112, 5264, 5479} Installing The 523-4908 Work Tool Positioner Kit {5112, 5264, 5479}