Engine Oil Filter and Oil Filter Base - Remove and Install
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 185-3630 | Strap Wrench As | 1 |
Show/hide table
 |
|
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Open the hood and remove the left side engine panel.
Show/hide table
Illustration 1 g06375047 - Drain the engine Oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures.
- Disconnect hose assembly (1). Use Tooling (A) to remove engine oil filter (2). Remove engine oil filter (2).
Show/hide table
Illustration 2 g06375050 - Remove bolts (3), bolts (6), bolts (5), and filter base (4).
- Remove tube assembly (7) and the O-ring seal from filter base (4).
- Install filter base (4) and engine oil filter (2) in the reverse order of removal.
- Lubricate the bore for the O-ring seal of tube assembly (7) lightly with the lubricant that is being sealed.
- Use the following procedure to tighten engine oil filter (2):
- Lubricate the seal and bore of engine oil filter (2) lightly with the lubricant that is being sealed. Install engine oil filter (2) in vertical orientation only.
- Tighten engine oil filter (2) to a torque of
100 ± 5 N.m (74 ± 4 lb ft) . - Ensure that there is no gap between engine oil filter (2) and filter base (4).
Caterpillar Information System:
C7.1 Engines and Generator Sets Exhaust System Contains Fuel
992K Wheel Loader Systems Pressure Switch (Steering Cooler Filter Bypass) (Steering Pump Case Drain Filter Bypass)
980L Tier 3 Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Coolant
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
992K Wheel Loader Systems Piston Pump (Implement, RH)
AD22 Underground Articulated Truck Oscillating Hitch - Lubricate
994K Wheel Loader Machine Systems Seat - Remove and Install
AD22 Underground Articulated Truck Oscillating Hitch - Adjust
A New Valve Mechanism Cover and Elbows Are Now Used on Certain 3412, C27, and C32 Machine Engines {1107} A New Valve Mechanism Cover and Elbows Are Now Used on Certain 3412, C27, and C32 Machine Engines {1107}
MD6310 Rotary Drill Air Compressor Oil Filter - Change
MD6310 Rotary Drill Air Compressor Oil - Change
C7.1 Engines and Generator Sets Exhaust System Contains Oil
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
C7.1 Engines and Generator Sets Fuel Contains Water
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
C7.1 Engines and Generator Sets Fuel Temperature Is High
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble
C7.1 Engines and Generator Sets Inlet Air Is Restricted
MD6250 Rotary Drill Air Filter Elements - Clean/Replace
980L Tier 3 Wheel Loader Engine Supplement Expansion Tank - Remove and Install
C7.1 Engines and Generator Sets Intake Manifold Air Pressure Is High
C7.1 Engines and Generator Sets Intake Manifold Air Pressure Is Low