Actuator Shutoff Valve {1317, 1329}
- Engine:
- 3044C (S/N: 3441471-1479,1676-1748,1821-1898,1902-1919,1926-1961,1965-1982,2016-2094,2131-2277,2290-2433,2449-2499,2632-2634,2644-2673,2740-2748,2992-2997,3028-3054,3067-3081,3181-3210,3232-3284,3286-3303,3470-3541,3643-3750,3985-4056)
Show/hide table
Illustration 1 | g01405454 |
Typical example |
There has been isolated instances of defects with the 243-4818 Shutoff Valve (1).
Show/hide table
Illustration 2 | g01405461 |
Use the following method to determine if there is a defect with the 243-4818 Shutoff Valve. Pull and twist the shutoff valve. Refer to illustration 2. If there is a defect with the 243-4818 Shutoff Valve, the defect will be in position (X). Check the shutoff valve when the next engine service is due. If necessary, replace the 243-4818 Shutoff Valve. Tighten the 243-4818 Shutoff Valve to a torque of 8 N·m (71 lb in).
Note: If there is a green mark on the 243-4818 Shutoff Valve, the 243-4818 Shutoff Valve has already been checked.
Caterpillar Information System:
G3408C and G3412C Engines Cylinder Head Valves
2007/08/27 Adjustment of the Alternator V-Belt {1154, 1357, 1405}
Oil Leakage Across C7 and C9 On-highway Engine Turbochargers{1052} Oil Leakage Across C7 and C9 On-highway Engine Turbochargers{1052}
C32 Marine Auxiliary Engine Engine Oil Level Gauge - Calibrate
345C Excavator Fuel Transfer Pump (Refueling) - If Equipped
Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000, 1408} Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000, 1408}
C7 On-Highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
C9 On-highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
C13 On-highway Engine Mounting Bracket (Idler Pulley)
C7 On-Highway Engine Clean Gas Induction Pressure Sensor - Remove and Install
G3520B Industrial Engines Ignition Timing - Adjust
2007/08/01 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
Incorrectly Identified Alternator Wiring on Some G3500 A3 Engines{1405, 1408} Incorrectly Identified Alternator Wiring on Some G3500 A3 Engines{1405, 1408}
C15 and C18 Petrolem Generator Set Engines Electrical Connectors - Inspect
Rework of the Internal Tray for the Harness{1408} Rework of the Internal Tray for the Harness{1408}
Injector Repair for C13 and C15 On-highway Engines{1290, 7620} Injector Repair for C13 and C15 On-highway Engines{1290, 7620}
G3520B Industrial Engines Nitrogen Oxide Level - Test
G3520B Industrial Engines Electrical Connectors
330F MHPU Mobile Hydraulic Power Unit Machine System Control Valve (Boom Lowering)
C7 Engine Oil Pressure Fault{1307, 1924} C7 Engine Oil Pressure Fault{1307, 1924}
Discoloration of the Hydraulic Cylinder Rod on Certain Excavators{5102, 5456, 5457, 5458, 5468, 7562} Discoloration of the Hydraulic Cylinder Rod on Certain Excavators{5102, 5456, 5457, 5458, 5468, 7562}
Removal and Installation of Electronic Unit Injectors{1290} Removal and Installation of Electronic Unit Injectors{1290}
345B Excavator Machine System Specifications Shuttle Valve (Pump Flow Control)
Product Link Registration Problems{733T, 7606} Product Link Registration Problems{733T, 7606}