C7 On-Highway Engine Caterpillar


Clean Gas Induction Pressure Sensor - Remove and Install

Usage:

C7 C7S

Removal Procedure

------ WARNING! ------

Sulfuric Acid Burn Hazard, may cause serious personal injury.

The clean gas induction (CGI) pressure sensor may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the CGI cooler during service of the engine and may travel to other downstream components. The sulfuric acid will burn the eyes, skin, and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.


Note: Put identification marks on all hoses and on all wires for installation purposes. Plug all hoses. This helps to keep contaminants from entering the system.



    Illustration 1g01404795

  1. Disconnect harness assembly (1).

  2. Disconnect hoses (4) (not shown).

  3. Remove bolt (3) and remove clean gas induction pressure sensor (2).

Installation Procedure

------ WARNING! ------

Sulfuric Acid Burn Hazard, may cause serious personal injury.

The clean gas induction (CGI) pressure sensor may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the CGI cooler during service of the engine and may travel to other downstream components. The sulfuric acid will burn the eyes, skin, and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.




    Illustration 2g01404795

  1. Position clean gas induction pressure sensor (2) and install bolt (3).

  2. Position clean gas induction pressure sensor (2) and install bolt (3). Tighten bolt (3) to a torque of 10 ± 2 N·m (89 ± 18 lb in).

  3. Connect hoses (4) and connect harness assembly (1).

Caterpillar Information System:

G3520B Industrial Engines Ignition Timing - Adjust
2007/08/01 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/20 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/27 Improved Engine Software is Used {7620}
G3408C and G3412C Engines Exhaust Manifold
Universal Joints and Drive Shafts {3108, 3251, 3253} Universal Joints and Drive Shafts {3108, 3251, 3253}
Reusability of Tapered Bearings {7000, 7551} Reusability of Tapered Bearings {7000, 7551}
Track Data Charts {0372, 0374, 4170} Track Data Charts {0372, 0374, 4170}
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism
C6.6 Engines For Caterpillar Built Machines Wastegate Solenoid - Test
Exhaust Rocker Arms with Oil Spray for Fuel Injector Solenoids on C7 and C9 On-highway Engines{1123, 1290} Exhaust Rocker Arms with Oil Spray for Fuel Injector Solenoids on C7 and C9 On-highway Engines{1123, 1290}
G3520B Industrial Engines Aftercooler
C13 On-highway Engine Mounting Bracket (Idler Pulley)
C9 On-highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
C7 On-Highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000, 1408} Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000, 1408}
345C Excavator Fuel Transfer Pump (Refueling) - If Equipped
C32 Marine Auxiliary Engine Engine Oil Level Gauge - Calibrate
Oil Leakage Across C7 and C9 On-highway Engine Turbochargers{1052} Oil Leakage Across C7 and C9 On-highway Engine Turbochargers{1052}
2007/08/27 Adjustment of the Alternator V-Belt {1154, 1357, 1405}
G3408C and G3412C Engines Cylinder Head Valves
2007/08/27 Actuator Shutoff Valve {1317, 1329}
Incorrectly Identified Alternator Wiring on Some G3500 A3 Engines{1405, 1408} Incorrectly Identified Alternator Wiring on Some G3500 A3 Engines{1405, 1408}
C15 and C18 Petrolem Generator Set Engines Electrical Connectors - Inspect
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.