Exhaust Manifold
Show/hide table
 | |
| Illustration 1 | g03320883 |
Show/hide table
 | |
| Illustration 2 | g03320887 |
Tightening sequence | |
Show/hide table
| Specification for 105-4663 Exhaust Manifold Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 4 | 6L-8562 Taperlock Stud | Torque to 35 ± 5 N·m (26 ± 4 lb ft). |
| 2 | 8 | 012-7950 Plug | Before assembly, apply Loctite C5A copper anti-seize to the threads and to the bearing surface. |
| 3 | 16 | 106-1792 Taperlock Stud | Torque to 35 ± 5 N·m (26 ± 4 lb ft). |
| 4 | 16 | 168-7800 Locknut | Before assembly, apply Loctite C5A copper anti-seize to the threads and to the bearing surface. Tighten the locknuts in the numerical sequence as shown in the Illustration 2 to 38 ± 5 N·m (28 ± 4 lb ft). |
| 5 | 8 | 5K-5959 O-Ring Seal | Before assembly, lightly lubricate the bore. |
| 6 | 1 | 4N-5073 Elbow | The cup plug must be removed from each cylinder head before the elbows are connected. |
| 7 | 1 | 5F-4899 Bolt | Torque to 54 ± 7 N·m (40 ± 5 lb ft). |
| 8 | 5 | 9S-8752 Full Nut | Before assembly, apply Loctite C5A copper anti-seize to the threads and bearing surface. |
| 9 | 1 | 6V-2605 Taperlock Stud | Before assembly, apply blue Loctite 242 to the threads. Torque to 35 ± 5 N·m (26 ± 4 lb ft). |
| 10 | 4 | 7L-0520 Taperlock Stud | Torque to 35 ± 5 N·m (26 ± 4 lb ft). |
| C | - | - | Distance between the top of the taperlock stud to cylinder head assembly is 66.2 ± 1.5 mm (2.61 ± 0.06 inch). |
Caterpillar Information System:
Universal Joints and Drive Shafts {3108, 3251, 3253} Universal Joints and Drive Shafts {3108, 3251, 3253}
Reusability of Tapered Bearings {7000, 7551} Reusability of Tapered Bearings {7000, 7551}
Track Data Charts {0372, 0374, 4170} Track Data Charts {0372, 0374, 4170}
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism
C6.6 Engines For Caterpillar Built Machines Wastegate Solenoid - Test
Exhaust Rocker Arms with Oil Spray for Fuel Injector Solenoids on C7 and C9 On-highway Engines{1123, 1290} Exhaust Rocker Arms with Oil Spray for Fuel Injector Solenoids on C7 and C9 On-highway Engines{1123, 1290}
G3520B Industrial Engines Aftercooler
14L Motor Grader Machine Systems Drawbar - Install
C15 and C18 Engines Air Shutoff - Test - If Equipped
Incorrect Part Number{1361} Incorrect Part Number{1361}
G3520B Industrial Engines Compressor Bypass
C32 Marine Auxiliary Engines Starting - Test
2007/08/27 Improved Engine Software is Used {7620}
2007/08/20 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/01 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
G3520B Industrial Engines Ignition Timing - Adjust
C7 On-Highway Engine Clean Gas Induction Pressure Sensor - Remove and Install
C13 On-highway Engine Mounting Bracket (Idler Pulley)
C9 On-highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
C7 On-Highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000, 1408} Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000, 1408}
345C Excavator Fuel Transfer Pump (Refueling) - If Equipped
C32 Marine Auxiliary Engine Engine Oil Level Gauge - Calibrate
Oil Leakage Across C7 and C9 On-highway Engine Turbochargers{1052} Oil Leakage Across C7 and C9 On-highway Engine Turbochargers{1052}