Cylinder Head Valves
注: 再使用和修补指南, "气门和气门弹簧技术规范"有用于检查使用过的气门和弹簧的必要步骤和技术规范。
Show/hide table
图 1 | g01381203 |
(1) 4N-5906 弹簧
- 在试验力下的长度 ... 54.99 mm (2.165 in)
- 试验力 ... 344 ± 34 N (77 ± 7.6 lb)
- 试验后的自由长度 ... 62.74 mm (2.470 in)
- 外径 ... 31.75 mm (1.250 in)
- 试验力 ... 344 ± 34 N (77 ± 7.6 lb)
(A) 至气门导管顶部的高度 ... 32.26 mm (1.270 in)
注: 安装到缸盖上之前,在气门杆上涂抹清洁的发动机机油。
(B) 新气门杆的直径 ... 9.441 ± 0.010 mm (0.3717 ± 0.0004 in)
缸盖中用于气门杆的最小直径
- 排气门 ... 9.309 mm (0.3665 in)
- 进气门 ... 9.309 mm (0.3665 in)
- 缸盖中用于安装新气门杆的孔 ... 9.487 ± 0.020 mm (0.3735 ± 0.0008 in)
- 进气门 ... 9.309 mm (0.3665 in)
(C) 气门盖直径
- 排气门 ... 41.81 ± 0.13 mm (1.646 ± 0.005 in)
- 进气门 ... 44.98 ± 0.13 mm (1.771 ± 0.005 in)
(D) 气门端面角度
- 排气门 ... 44.25 ± 0.25 度
- 进气门 ... 29.25 ± 0.25 度
Show/hide table
图 2 | g01381208 |
(E) 气门座圈的直径
- 排气门 ... 42.850 ± 0.013 mm (1.6870 ± 0.0005 in)
- 进气门 ... 46.025 ± 0.013 mm (1.8120 ± 0.0005 in)
(F) 缸盖中用于新气门座圈的孔深 ... 15.7 ± 0.5 mm (0.62 ± 0.02 in)
缸盖上的气门座孔
- 排气门 ... 42.774 ± 0.025 mm (1.6840 ± 0.0010 in)
- 进气门 ... 45.949 ± 0.025 mm (1.8090 ± 0.0010 in)
(G) 气门的突出高度
- 进气门和排气门从缸盖面的最大允许突出量 ... −1.219 至 0.203 mm (−0.0480 至 0.0080 in)
(H) 气门座圈的面角
- 排气门 ... 44.75 ± 0.50 度
- 进气门 ... 30.25 ± 0.50 度
(J) 气门座圈端面
- 排气门座 ... 39.268 mm (1.5460 in)
- 进气门座 ... 40.894 mm (1.6100 in)
Caterpillar Information System:
C7 and C9 Petroleum Engines Alternator Problem - Charging Problem and/or Noisy Operation
C7 and C9 Petroleum Engines Acceleration Is Poor or Throttle Response Is Poor
3512C Engine Air Shutoff - Test
C32 Marine Engine Electrical Connectors
C18 Generator set and C18 Marine Engines Water Lines - Remove and Install
C4.4 (Mech) Industrial Engine V-Belt - Test
C7 and C9 Petroleum Engines Welding Precaution
C7 and C9 Petroleum Engines General Information
C32 Marine Propulsion Engines Event Code List
C7 and C9 On-Highway Engines Fuel System Pressure - Test
C32 Marine Propulsion Engines Diagnostic Code Cross Reference
C32 Marine Propulsion Engines Diagnostic Trouble Code List
3512C Engine Diagnostic Trouble Codes
3512C Engine Event Codes
3408E and 3412E Engines for Caterpillar Built Machines Valve Mechanism Cover
2007/06/04 A New Alternator Drive Pulley with an Improved Wear Sleeve is Used {1154, 1405, 1425}
2007/07/09 A New Water Pump Seal Is Now Available {1361, 7555}
C7 and C9 Petroleum Engines Cylinder Is Noisy
C7 and C9 Petroleum Engines Engine Does Not Crank
C7 and C9 Petroleum Engines Engine Misfires, Runs Rough or Is Unstable
C7 and C9 Petroleum Engines Engine Shutdown Is Intermittent
C7 and C9 Petroleum Engines Engine Stalls at Low RPM
C7 and C9 Petroleum Engines Exhaust Has Excessive Black Smoke
C7 and C9 Petroleum Engines Exhaust Has Excessive White Smoke