Diagnostic Code Cross Reference
Problems with the electronic control system can be reported via flash codes or diagnostic trouble codes. Flash codes provide an indication of a problem with a specific engine subsystem. Diagnostic trouble codes provide information on the engine subsystem and information that is related to the failure mode of the problem.
Table 1 and Table 2 list the cross-reference information that is necessary to locate the circuit test that will assist in diagnosing electrical problems for the engine subsystems. To diagnose a problem with a flash code that is known, locate the flash code in the table and perform the related circuit test that is listed.
For information on diagnostic codes, refer to Troubleshooting, "Diagnostic Trouble Code List".
Cross-Reference for Flash Code to CID-FMI and Event Code
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Show/hide table
| Cross-Reference from Flash Code to CID-FMI Code/Event Code and Description to Troubleshooting Procedure | ||
|---|---|---|
| Flash Code | CID-FMI Code/Event Code and Description | Procedure |
| N/A | E056(1) High Fuel Temperature Warning | Troubleshooting, "Fuel Temperature is High" |
| E096(1) High Fuel Pressure | Troubleshooting, "Fuel Pressure Is High" | |
| E119(1) Low Fuel Level | Add fuel to the fuel tank. Refer to the literature that is provided by the OEM of the vessel for the correct procedure. | |
| E173(1) High Exhaust Temperature Warning | Troubleshooting, "Exhaust Temperature Is High" | |
| 261-11 Engine Timing Offset fault | Troubleshooting, "Timing - Calibrate" | |
| 268-2 Programmed Parameter Fault erratic, intermittent, or incorrect | Troubleshooting, "Configuration Parameters" | |
| 535-8 Exhaust Temperature Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Sensor Signal (PWM) - Test" | |
| 13 | 174-3 Fuel Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 174-4 Fuel Temperature Sensor voltage below normal | ||
| 15 | 96-3 Fuel Level Sensor voltage above normal | Troubleshooting, "Fuel Level - Test" |
| 96-4 Fuel Level Sensor voltage below normal | ||
| 17 | 168-0 Electrical System Voltage high - most severe (3) | Troubleshooting, "Electrical Power Supply - Test" |
| 21 | 41-3 8 Volt DC Supply voltage above normal | Troubleshooting, "Sensor Supply - Test" |
| 41-4 8 Volt DC Supply voltage above normal | ||
| 262-3 5 Volt Sensor DC Power Supply voltage above normal | ||
| 262-4 5 Volt Sensor DC Power Supply voltage below normal | ||
| 23 | 175-3 Engine Oil Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 175-4 Engine Oil Temperature Sensor voltage below normal | ||
| 24 | 100-3 Engine Oil Pressure Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 100-4 Engine Oil Pressure Sensor voltage below normal | ||
| 100-10 Engine Oil Pressure Sensor abnormal rate of change | ||
| 25 | 1785-3 Intake Manifold Pressure Sensor voltage above normal | |
| 1785-4 Intake Manifold Pressure Sensor voltage below normal | ||
| 1785-10 Intake Manifold Pressure Sensor abnormal rate of change | ||
| 27 | 110-3 Engine Coolant Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 110-4 Engine Coolant Temperature Sensor voltage below normal | ||
| 28 | 91-13 Throttle Position Sensor calibration required | Troubleshooting, "Throttle Position Sensor - Calibrate" |
| 1249-13 Secondary Throttle Position calibration required | ||
| 32 | 91-8 Throttle Position Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Speed Control - Test" |
| 1249-8 Secondary Throttle Position signal abnormal | ||
| 34 | 190-8 Engine Speed Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Speed/Timing - Test" |
| 342-8 Secondary Engine Speed Sensor abnormal frequency, pulse width, or period | ||
| 35 | E190(1) Engine Overspeed Warning | Troubleshooting, "Engine Overspeeds" |
| 36 | E268(1) Unexpected Engine Shutdown | Troubleshooting, "Engine Shutdown Occurrence" |
| 37 | 94-3 Fuel Delivery Pressure Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 94-4 Fuel Delivery Pressure Sensor voltage below normal | ||
| 38 | 172-3 Intake Manifold Air Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 172-4 Intake Manifold Air Temperature Sensor voltage below normal | ||
| 42 | 261-13 Engine Timing Calibration calibration required | Troubleshooting, "Timing - Calibrate" |
| 46 | E039(2) Low Engine Oil Pressure Derate | Troubleshooting, "Oil Pressure Is Low" |
| E100(1) Low Engine Oil Pressure Warning | ||
| 51 | 168-1 Electrical System Voltage low - most severe (3) | Troubleshooting, "Electrical Power Supply - Test" |
| 168-2 Electrical System Voltage erratic, intermittent, or incorrect | ||
| 58 | E057(2) Low Engine Coolant Level Derate | Troubleshooting, "Coolant Level Is Low" |
| E059(1) Low Engine Coolant Level Warning | ||
| 59 | 253-2 Personality Module erratic, intermittent, or incorrect | Troubleshooting, "ECM Software - Install" |
| 61 | E015(2) High Engine Coolant Temperature Derate | Troubleshooting, "Coolant Temperature Is High" |
| E017(1) High Engine Coolant Temperature Warning | ||
| 63 | E053(1) Low Fuel Pressure Warning | Troubleshooting, "Fuel Pressure Is Low" |
| 64 | E025(2) High Inlet Air Temperature Derate | Troubleshooting, "Inlet Air Temperature Is High" |
| E027(1) High Inlet Air Temperature Warning | ||
| 66 | E030(1) High Transmission Oil Temperature Warning | Troubleshooting, "Transmission Oil Temperature Is High" |
| 67 | 177-3 Transmission Oil Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 177-4 Transmission Oil Temperature Sensor voltage below normal | ||
| 68 | 127-3 Transmission Oil Pressure Sensor voltage above normal | |
| 127-4 Transmission Oil Pressure Sensor voltage below normal | ||
| 69 | E113(1) High Transmission Oil Pressure | Troubleshooting, "Transmission Oil Pressure Is High" |
| 71 | 1-5 Cylinder #1 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 1-6 Cylinder #1 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 72 | 2-5 Cylinder #2 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 2-6 Cylinder #2 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 73 | 3-5 Cylinder #3 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 3-6 Cylinder #3 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 74 | 4-5 Cylinder #4 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 4-6 Cylinder #4 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 75 | 5-5 Cylinder #5 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 5-6 Cylinder #5 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 76 | 6-5 Cylinder #6 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 6-6 Cylinder #6 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 77 | 7-5 Cylinder #7 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 7-6 Cylinder #7 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 78 | 8-5 Cylinder #8 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 8-6 Cylinder #8 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 81 | 9-5 Cylinder #9 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 9-6 Cylinder #9 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 82 | 10-5 Cylinder #10 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 10-6 Cylinder #10 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 83 | 11-5 Cylinder #11 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 11-6 Cylinder #11 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
| 84 | 12-5 Cylinder #12 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 12-6 Cylinder #12 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" | |
Cross-Reference for SPN-FMI code to CID-FMI and Event Code
Show/hide table
| Cross-Reference from SPN-FMI Code to CID-FMI Code/Event Code and Description to Troubleshooting Procedure | ||
|---|---|---|
| SPN-FMI Code | CID-FMI Code/Event Code and Description | Procedure |
| N/A | 827-8 Left Exhaust Temperature Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Sensor Signal (PWM) - Test" |
| 828-8 Right Exhaust Temperature Sensor abnormal frequency, pulse width, or period | ||
| 1632-09 Backup Engine Control Module abnormal update rate | Troubleshooting, "Cat Data Link - Test" | |
| E190(1) Engine Overspeed Warning | Troubleshooting, "Engine Overspeeds" | |
| E552(1) Low Aftercooler Coolant Level Warning | Troubleshooting, "Coolant Level Is Low" | |
| E552(2) Low Aftercooler Coolant Level Derate | ||
| 29-8 | 1249-8 Secondary Throttle Position signal abnormal | Troubleshooting, "Speed Control - Test" |
| 29-13 | 1249-13 Secondary Throttle Position calibration required | Troubleshooting, "Throttle Position Sensor - Calibrate" |
| 91-8 | 91-8 Throttle Position Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Speed Control - Test" |
| 91-13 | 91-13 Throttle Position Sensor calibration required | Troubleshooting, "Throttle Position Sensor - Calibrate" |
| 94-15 | E096(1) High Fuel Pressure | Troubleshooting, "Fuel Pressure Is High" |
| 94-3 | 94-3 Fuel Delivery Pressure Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 94-4 | 94-4 Fuel Delivery Pressure Sensor voltage below normal | |
| 94-17 | E053(1) Low Fuel Pressure Warning | Troubleshooting, "Fuel Pressure Is Low" |
| 96-3 | 96-3 Fuel Level Sensor voltage above normal | Troubleshooting, "Fuel Level - Test" |
| 96-4 | 96-4 Fuel Level Sensor voltage below normal | |
| 96-17 | E119(1) Low Fuel Level | Add fuel to the fuel tank. Refer to the literature that is provided by the OEM of the vessel for the correct procedure. |
| 100-3 | 100-3 Engine Oil Pressure Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 100-4 | 100-4 Engine Oil Pressure Sensor voltage below normal | |
| 100-10 | 100-10 Engine Oil Pressure Sensor abnormal rate of change | |
| 100-17 | E100(1) Low Engine Oil Pressure Warning | Troubleshooting, "Oil Pressure Is Low" |
| 100-18 | E039(2) Low Engine Oil Pressure Derate | |
| 102-3 | 1785-3 Intake Manifold Pressure Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 102-4 | 1785-4 Intake Manifold Pressure Sensor voltage below normal | |
| 102-10 | 1785-10 Intake Manifold Pressure Sensor abnormal rate of change | |
| 105-3 | 172-3 Intake Manifold Air Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 105-4 | 172-4 Intake Manifold Air Temperature Sensor voltage below normal | |
| 110-3 | 110-3 Engine Coolant Temperature Sensor voltage above normal | |
| 110-4 | 110-4 Engine Coolant Temperature Sensor voltage below normal | |
| 110-15 | E017(1) High Engine Coolant Temperature Warning | Troubleshooting, "Coolant Temperature Is High" |
| 110-16 | E015(2) High Engine Coolant Temperature Derate | |
| 111-17 | E059(1) Low Engine Coolant Level Warning | Troubleshooting, "Coolant Level Is Low" |
| 111-18 | E057(2) Low Engine Coolant Level Derate | |
| 127-3 | 127-3 Transmission Oil Pressure Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 127-4 | 127-4 Transmission Oil Pressure Sensor voltage below normal | |
| 127-15 | E113(1) High Transmission Oil Pressure | Troubleshooting, "Transmission Oil Pressure Is High" |
| 158-2 | 1834-02 Ignition Key Switch loss of signal | |
| 168-0 | 168-0 Electrical System Voltage high - most severe (3) | Troubleshooting, "Electrical Power Supply - Test" |
| 168-1 | 168-1 Electrical System Voltage low - most severe (3) | |
| 168-2 | 168-2 Electrical System Voltage erratic, intermittent, or incorrect | |
| 172-15 | E027(1) High Inlet Air Temperature Warning | Troubleshooting, "Inlet Air Temperature Is High" |
| 172-16 | E025(2) High Inlet Air Temperature Derate | |
| 173-08 | 535-8 Exhaust Temperature Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Sensor Signal (PWM) - Test" |
| 173-15 | E173(1) High Exhaust Temperature Warning | Troubleshooting, "Exhaust Temperature Is High" |
| 173-16 | E021(2) High Exhaust Temperature Derate | |
| 174-3 | 174-3 Fuel Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 174-4 | 174-4 Fuel Temperature Sensor voltage below normal | |
| 174-15 | E056(1) High Fuel Temperature Warning | Troubleshooting, "Fuel Temperature is High" |
| 175-3 | 175-3 Engine Oil Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
| 175-4 | 175-4 Engine Oil Temperature Sensor voltage below normal | |
| 175-15 | E020(1) High Engine Oil Temperature Warning | Troubleshooting, "Oil Temperature Is High" |
| 175-16 | E018(2) High Engine Oil Temperature Derate | |
| 177-3 | 177-3 Transmission Oil Temperature Sensor voltage above normal | Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
| 177-4 | 177-4 Transmission Oil Temperature Sensor voltage below normal | |
| 177-15 | E030(1) High Transmission Oil Temperature Warning | Troubleshooting, "Transmission Oil Temperature Is High" |
| 190-8 | 190-8 Engine Speed Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Speed/Timing - Test" |
| 228-13 | 261-13 Engine Timing Calibration calibration required | Troubleshooting, "Timing - Calibrate" |
| 620-3 | 262-3 5 Volt Sensor DC Power Supply voltage above normal | Troubleshooting, "Sensor Supply - Test" |
| 620-4 | 262-4 5 Volt Sensor DC Power Supply voltage below normal | |
| 631-02 | 253-2 Personality Module erratic, intermittent, or incorrect | Troubleshooting, "ECM Software - Install" |
| 637-11 | 261-11 Engine Timing Offset fault | Troubleshooting, "Timing - Calibrate" |
| 651-5 | 1-5 Cylinder #1 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 651-6 | 1-6 Cylinder #1 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 652-5 | 2-5 Cylinder #2 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 652-6 | 2-6 Cylinder #2 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 653-5 | 3-5 Cylinder #3 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 653-6 | 3-6 Cylinder #3 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 654-5 | 4-5 Cylinder #4 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 654-6 | 4-6 Cylinder #4 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 655-5 | 5-5 Cylinder #5 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 655-6 | 5-6 Cylinder #5 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 656-5 | 6-5 Cylinder #6 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 656-6 | 6-6 Cylinder #6 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 657-5 | 7-5 Cylinder #7 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 657-6 | 7-6 Cylinder #7 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 658-5 | 8-5 Cylinder #8 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 658-6 | 8-6 Cylinder #8 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 659-5 | 9-5 Cylinder #9 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 659-6 | 9-6 Cylinder #9 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 660-5 | 10-5 Cylinder #10 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 660-6 | 10-6 Cylinder #10 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 661-5 | 11-5 Cylinder #11 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 661-6 | 11-6 Cylinder #11 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 662-5 | 12-5 Cylinder #12 Injector current below normal | Troubleshooting, "Injector Solenoid - Test" |
| 662-6 | 12-6 Cylinder #12 Injector current above normal | Troubleshooting, "Injector Solenoid - Test" |
| 678-3 | 41-3 8 Volt DC Supply voltage above normal | Troubleshooting, "Sensor Supply - Test" |
| 678-4 | 41-4 8 Volt DC Supply voltage above normal | |
| 723-8 | 342-8 Secondary Engine Speed Sensor abnormal frequency, pulse width, or period | Troubleshooting, "Speed/Timing - Test" |
| 1111-2 | 268-2 Programmed Parameter Fault erratic, intermittent, or incorrect | Troubleshooting, "Configuration Parameters" |
| 1383-11 | E268(1) Unexpected Engine Shutdown | Troubleshooting, "Engine Shutdown Occurrence" |
Caterpillar Information System:
C32 Marine Propulsion Engines Diagnostic Trouble Code List
C32 Marine Engine Configuration Parameters
C15 On-Highway Engine Exhaust Manifold - Remove and Install
C32 Marine Propulsion Engines Cat Data Link - Test
3600 and C280 Diesel Engine Fluids Recommendations S·O·S Services Coolant Analysis
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Head
3408E and 3412E Engines for Caterpillar Built Machines Camshaft
C32 Marine Propulsion Engines CAN Data Link - Test
3512C HD and 3516C HD IPP Rental Power Modules Inlet Air Is Restricted
2007/07/02 The Firing Order has Changed for New Engines {1000}
C15 On-Highway Engine Fumes Disposal Group - Remove and Install
C32 Marine Propulsion Engines Sensor Signal (PWM) - Test
C7 and C9 On-Highway Engines Fuel System Pressure - Test
C32 Marine Propulsion Engines Event Code List
C7 and C9 Petroleum Engines General Information
C7 and C9 Petroleum Engines Welding Precaution
C4.4 (Mech) Industrial Engine V-Belt - Test
C18 Generator set and C18 Marine Engines Water Lines - Remove and Install
C32 Marine Engine Electrical Connectors
3512C Engine Air Shutoff - Test
C7 and C9 Petroleum Engines Acceleration Is Poor or Throttle Response Is Poor
C7 and C9 Petroleum Engines Alternator Problem - Charging Problem and/or Noisy Operation
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Head Valves
3512C Engine Diagnostic Trouble Codes