320D and 323D Excavators Machine System Specifications Caterpillar

Stick

Usage:

323D L BYM

Show/hide table




Illustration 1	g03818434
Right side view 290-9216 Hoe Stick Gp ( 2.5 m (8.20 ft)) 375-6280 Hoe Stick Gp ( 2.5 m (8.20 ft)) 241-7306 Hoe Stick Gp ( 2.5 m (8.20 ft)) 315-1040 Hoe Stick Gp ( 3.86 m (12.664 ft)) 290-9225 Hoe Stick Gp ( 1.9 m (6.23 ft))

Show/hide table

Table 1
Specification for 290-9216 Hoe Stick Gp, 375-6280 Hoe Stick Gp, 241-7306 Hoe Stick Gp, and 315-1040 Hoe Stick Gp
Item	Qty	Part	Specification Description
All bores must be free of paint. Use 5P-0960 Grease Cartridge to coat all bores for the pins, the bucket, and the cylinder pin bores.
1	1	4I-4811 Pin As	Diameter is 69.850 ± 0.025 mm (2.7500 ± 0.0010 inch).
2	1	4I-4809 Pin As	Diameter is 79.850 ± 0.025 mm (3.1437 ± 0.0010 inch).
3	2	166-1495 Lip Type Seal	Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss.
4	2	235-7679 Lip Type Seal	Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss.
5	2	166-1494 Lip Type Seal	Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss.
Install the following bushings in the bore so that the part number of the bushing is facing outward.
6	Bushing (6) is one of the following part numbers:
	2	228-5615 Bushing	Bore before Installation is 90.21 ± 0.04 mm (3.552 ± 0.002 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).
	2	244-4277 Bushing	Bore before Installation is 90.16 ± 0.02 mm (3.550 ± 0.001 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).
7	2	229-1096 Bushing	Install the bushing in the bore so that the part number of the bushing is facing outward. Bore before Installation is 70.17 ± 0.04 mm (2.763 ± 0.002 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).
8	2	240-2913 Bushing	Install the bushing in the bore so that the part number of the bushing is facing outward. Bore before Installation is 80.20 ± 0.04 mm (3.157 ± 0.002 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).

Caterpillar Information System:

C15 On-Highway Engine Cylinder Head - Install

C4.4 (Mech) Industrial Engine Turbocharger - Inspect

G3520B Industrial Engines Cat Data Link - Test

G3520B Industrial Engines Detonation - Test

G3520B Industrial Engines Electrical Power Supply - Test

C15 On-Highway Engine Clean Gas Induction Pressure Sensor - Remove and Install

G3520B Industrial Engines Fuel Metering Valve - Test

G3520B Industrial Engines Ignition Primary - Test

G3520B Industrial Engines Ignition Secondary - Test

C4.4 (Mech) Industrial Engine General Information

3408B and 3408C Industrial and Marine Engines Engine Oil Lines

G3520B Industrial Engines Indicator Lamp - Test

C32 Marine Propulsion Engines Sensor Supply - Test

G3520B Industrial Engines ECM - Replace

G3520B Industrial Engines Control Module - Replace

C15 On-Highway Engine Compression Brake Lash - Adjust

G3520B Industrial Engines Coolant Temperature Is High

G3500B Engines Coolant Pressure Is Low

G3500B Engines Coolant Temperature Is Low

3500 and 3500B Engines Camshaft Roller Followers - Inspect

Inspecting and Repairing the Air Inlet and Exhaust System After Improper Fueling{1000, 1052, 1053, 1061, 1087} Inspecting and Repairing the Air Inlet and Exhaust System After Improper Fueling{1000, 1052, 1053, 1061, 1087}

G3520B Industrial Engines Timing - Calibrate

C15 and C18 Petrolem Generator Set Engines Speed/Timing - Test

G3500B Engines Engine Does Not Crank