Turbocharger - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | QTY     |
A     | 4C-5599     | Anti-Seize Compound     | 1     |
Start By:
- Remove the exhaust elbow.
- Refer to Operation and Maintenance Manual, "Coolant - Change" for the proper draining and filling procedures.
- Disconnect clamp assembly (2) and remove diffuser (1) from the turbocharger.
Show/hide table
Illustration 1 | g02170055 |
- Disconnect tube assemblies (3) and (4) .
- Disconnect hose assemblies (5) and (7) .
Show/hide table
Illustration 2 | g01864534 |
- Disconnect tube assembly (6) .
- Attach a suitable lifting device to turbocharger (8). The weight of turbocharger (8) is approximately 26 kg (57 lb).
- Remove nuts (9) and turbocharger (8). Discard the gasket and nuts (9) .
- If needed, carefully remove clamp assemblies (2) and (10). Discard the clamp assemblies.
Show/hide table
Illustration 3 | g02225358 |
Installation Procedure
- Install turbocharger (8) in the reverse order of removal.
- Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation. This action will provide lubrication during start-up and during storage.
- Tighten new clamp assemblies (10) to a torque of 13.6 ± 1.2 N·m (120 ± 11 lb in).
- Tighten new clamp assemblies (2) to a torque of 12 ± 4 N·m (106 ± 35 lb in).
- Apply Tooling (A) to the threads of new nuts (9) prior to installation. Tighten nuts (9) to a torque of 70 ± 5 N·m (52 ± 4 lb ft).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
2013/06/10 Procedure to Rework the Alternator Guard Now Available for AD30 Underground Articulated Trucks {7174}
Procedure to Rework the Start Relay Magnetic Switch on Certain Underground Articulated Trucks {7499} Procedure to Rework the Start Relay Magnetic Switch on Certain Underground Articulated Trucks {7499}
924K, 930K and 938K Wheel Loaders Electronic Control Module (ECM)
924K, 930K and 938K Wheel Loaders Alternator
2013/07/18 Bolts Have Been Added to the Sweep Mount Bracket on Certain Wheel Skidders {7162}
2013/06/13 New Fenders with Improved Gussets Are Now Used on Certain Grapple Skidders {7252}
988K XE Wheel Loader Calibrations (Operator Monitor)
988K XE Wheel Loader Brake Accumulator
Caterpillar Wheel Loader and Wheel Dozer (834 - 854, 992 - 994) Technician Checklist Engine and Torque Converter (TC) Removal and Installation {0372, 0374, 1000, 1000, 1003, 1003, 3101, 3101} Caterpillar Wheel Loader and Wheel Dozer (834 - 854, 992 - 994) Technician Checklist Engine and Torque Converter (TC) Removal and Installation {0372, 0374, 1000, 1000, 1003, 1003, 3101, 3101}
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install
C13 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install