Fuel Filter Base - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 185-3630     | Strap Wrench As     | 1     |
B     | −     | Loctite 271     | −     |
- Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
- Cut clips (1) and remove hose assemblies (2) and the fittings.
Note: Depending on the machine application, the fuel filter assembly will be mounted in various places on a machine. The following procedure is a general procedure for servicing the fuel filter base. Refer to the machine-specific engine supplement manual for more specific instructions.
Show/hide table
Illustration 1 | g02845402 |
- Disconnect the harness assembly from fuel temperature sensor (3). Remove temperature sensor (3) .
Show/hide table
Illustration 2 | g02845417 |
- Disconnect the harness assembly from pre-filter fuel pressure sensor (4). Remove pressure sensor (4) .
- Use Tooling (A) to remove fuel filters (5). Remove fuel filter base (6) .
- Remove adapter assembly (7) and studs (8) .
Show/hide table
Illustration 3 | g02845480 |
Installation Procedure
- Install fuel filter base (6) in reverse order of removal.
- Apply Tooling (B) to the threads of studs (8). Tooling (B) should cover the threads of the stud, shown as Distance (C), which is a measurement of 7.6 ± 0.8 mm (0.3 ± 0.03 inch).
Show/hide tableIllustration 4 g02845499
- Tighten studs (8) to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
- Tighten fuel temperature sensor (1) to a torque of 20 ± 3 N·m (177 ± 26 lb in).
- Tighten pre-filter fuel pressure sensor (2) to a torque of 10 ± 2 N·m (88 ± 17 lb in).
- Lubricate the fuel filter seals with the fluid that is being sealed prior to installation. Use Tooling (A) to tighten the fuel filters (5) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
2013/06/10 Procedure to Rework the Alternator Guard Now Available for AD30 Underground Articulated Trucks {7174}
Procedure to Rework the Start Relay Magnetic Switch on Certain Underground Articulated Trucks {7499} Procedure to Rework the Start Relay Magnetic Switch on Certain Underground Articulated Trucks {7499}
924K, 930K and 938K Wheel Loaders Electronic Control Module (ECM)
924K, 930K and 938K Wheel Loaders Alternator
2013/07/18 Bolts Have Been Added to the Sweep Mount Bracket on Certain Wheel Skidders {7162}
2013/06/13 New Fenders with Improved Gussets Are Now Used on Certain Grapple Skidders {7252}
988K XE Wheel Loader Calibrations (Operator Monitor)
988K XE Wheel Loader Brake Accumulator
Caterpillar Wheel Loader and Wheel Dozer (834 - 854, 992 - 994) Technician Checklist Engine and Torque Converter (TC) Removal and Installation {0372, 0374, 1000, 1000, 1003, 1003, 3101, 3101} Caterpillar Wheel Loader and Wheel Dozer (834 - 854, 992 - 994) Technician Checklist Engine and Torque Converter (TC) Removal and Installation {0372, 0374, 1000, 1000, 1003, 1003, 3101, 3101}
854K Wheel Dozer and 992K Wheel Loader Machine Systems Ripper Control Valve - Remove and Install
D9T Track-Type Tractor Systems Hydraulic Fan Speed (On Demand) - Test and Adjust
C13 Engine for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install