TA19-M2WD and TA19-M4WD Agricultural Transmissions Caterpillar


Relief Valve (Transmission Lubrication)

Usage:

TA19-M2WD T2Z



Illustration 1g01316742

(1) Transmission lubrication relief valve




Illustration 2g00646729

(1) Transmission lubrication relief valve

(2) Spool

(3) Spring

(4) Ports to the transmission case

(5) Passage from the transmission hydraulic control

The transmission lubrication relief valve (1) is located after the relief valve for the transmission hydraulic control. Transmission lubrication relief valve (1) controls the maximum pressure of the lubrication oil that is flowing to the transmission. Lubrication oil for the transmission comes from oil that is flowing through the pressure relief valve for the transmission charging system. When the oil from the transmission charging section of the transmission gear pump reaches the relief setting, oil will pass through the pressure relief valve for the transmission charging system. This oil is then supplied to the transmission as lubricating oil. If the pressure of the lubrication oil in the transmission lubrication relief valve (1) overcomes the force of spring (3), spool (2) will shift. This will allow passage (5) to drain lubrication oil through ports (4) into the transmission case.

Caterpillar Information System:

345C Excavator Machine System Specifications Swing Gear and Bearing
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Basic Engine
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Clutch
G3304 and G3306 Engines Turbocharger
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Engine Oil and Filter - Change
3508C, 3512C and 3516C Marine Engines Flywheel Housing - Install
2014/08/08 New Cylinder Head Groups Are Used For Certain 3500 Engines {1100}
3508C, 3512C and 3516C Marine Engines Flywheel Housing - Remove
CAESultra Installation for Wheel Loaders, Wheel Dozers, Landfill Compactors, and Motor Graders {7604, 7620} CAESultra Installation for Wheel Loaders, Wheel Dozers, Landfill Compactors, and Motor Graders {7604, 7620}
TH48-E70-C27I, TH48-E70-C32I and TH48-E70-C32P Petroleum Power Train packages and TH48-E70 Petroleum Transmission Power Train Electronic Control System Starting System
C0.5 and C0.7 Industrial Engines Cooling System Water Temperature Regulator - Replace
C280-6 and C280-8 Engines Engine Lifting Bracket - Remove and Install
TA19-M2WD and TA19-M4WD Agricultural Transmissions General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Wear Sleeve (Rear) - Remove and Install
3500C Marine Auxiliary Engines System Overview
3500C Marine Propulsion Engines Component Location
C0.5 and C0.7 Industrial Engines Fuel System Primary Filter/Water Separator - Drain
TA19-M2WD and TA19-M4WD Agricultural Transmissions Visual Inspection
TA19-M2WD and TA19-M4WD Agricultural Transmissions Clutch (Front Wheel Assist)
2006/10/16 New Information Has Been Added in Testing and Adjusting , "Position Switch (Service Brake Pedal) - Adjust" {4269}
C32 Power Module Plate Locations and Film Locations
C7 On-highway Engine Engine to Transmission Adapter
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Reference Material
C7 On-highway Engine Engine to Transmission Adapter
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.