Starting System
系统运作描述:
ECM 会在钥匙起动开关处于起动位置且方向开关处于空档位置时启用起动继电器。 ECM 检测到一个起动继电器电路及电气系统中的故障。 如果存在 CID 0444 或 CID 0168,则在检查钥匙起动开关前,必须排除诊断代码。 请参阅故障诊断与排除, "诊断代码列表"。
测试步骤 1. 检查钥匙起动开关在起动位置。
- 确保不存在 CID 0444 诊断代码。 如果存在该诊断代码,在操作之前先排除故障。
- 从机器线束上断开 ECM。
- 将断路开关转到接通位置。
- 将钥匙起动开关转到并保持在起动位置。
- 在 ECM 机器线束接头上,测量触点 J2-1(导线 307-OR)与触点 J1-70(接地)之间的电压。
预期结果:
应存在蓄电池正极电压。
结果:
- 是 - 存在蓄电池正极电压。 转至测试步骤 2。
- 否 - 不存在蓄电池正极电压。 钥匙起动开关或机器线束(导线 307-OR)出故障。 检查钥匙起动开关和机器线束。
修复: 如有必要,更换钥匙起动开关和/或机器线束。
停止
测试步骤 2. 检查钥匙起动开关在断开位置。
- ECM 仍保持从机器线束上断开的状态。
- 将钥匙起动开关转到断开位置。
- 在 ECM 机器线束接头上,测量触点 J2-1(导线 307-OR)与触点 J1-70(接地)之间的电压。
预期结果:
应存在蓄电池正极电压。
结果:
- 是 - 存在蓄电池正极电压。 钥匙起动开关或机器线束(导线 307-OR)出故障。 检查钥匙起动开关和机器线束。
修复: 如有必要,更换钥匙起动开关和/或机器线束。
停止
- 否 - 不存在蓄电池正极电压。 线束电路工作正常。 ECM 可能出现故障。
修复: ECM 不太可能会出现故障。 再次执行这些测试步骤。 如果没有找到原因,则需更换 ECM。 请参考测试和调整, "电子控制模块 (ECM) - 更换 "。
停止
Caterpillar Information System:
C0.5 and C0.7 Industrial Engines Cooling System Water Temperature Regulator - Replace
C280-6 and C280-8 Engines Engine Lifting Bracket - Remove and Install
TA19-M2WD and TA19-M4WD Agricultural Transmissions Maintenance Interval Schedule
C280-12 and C280–16 Marine Engines Engine Lifting Bracket - Remove and Install
2006/10/16 New Software Available for Product Link {7606, 7620}
2006/11/13 New Software is Now Available for EMCP 3.1, EMCP 3.2, and EMCP 3.3 {4490, 7620}
C0.5 and C0.7 Industrial Engines Fuel Injector - Test/Change
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Suction Screen - Clean
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil Level - Check
Bench Test Procedure For A TH48FT - E70 Oil Field Transmission {3030} Bench Test Procedure For A TH48FT - E70 Oil Field Transmission {3030}
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil - Change
TA19-M2WD and TA19-M4WD Agricultural Transmissions Breather (Transmission) - Clean
CAESultra Installation for Wheel Loaders, Wheel Dozers, Landfill Compactors, and Motor Graders {7604, 7620} CAESultra Installation for Wheel Loaders, Wheel Dozers, Landfill Compactors, and Motor Graders {7604, 7620}
3508C, 3512C and 3516C Marine Engines Flywheel Housing - Remove
2014/08/08 New Cylinder Head Groups Are Used For Certain 3500 Engines {1100}
3508C, 3512C and 3516C Marine Engines Flywheel Housing - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Engine Oil and Filter - Change
G3304 and G3306 Engines Turbocharger
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Clutch
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Basic Engine
345C Excavator Machine System Specifications Swing Gear and Bearing
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Lubrication)
TA19-M2WD and TA19-M4WD Agricultural Transmissions General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Wear Sleeve (Rear) - Remove and Install