Transmission Suction Screen - Clean
Show/hide table
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
Note: The suction screen can be found on the right hand side of the front of the transmission.
Note: It is not necessary to drain the transmission oil before removing the suction screen.
Show/hide table
Illustration 1 | g01315755 |
- Remove four bolts (1) from end cover (2) .
- Remove suction screen (3) from the housing.
Show/hide table
Illustration 2 | g01296091 |
- Wash the screen in a clean, nonflammable solvent.
- Inspect the screen for any damage. The screen may be damaged. Replace the screen with a new screen.
- Install clean suction screen (3) into the case housing.
- Reinstall end cover (2) with four bolts (1) .
Caterpillar Information System:
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil Level - Check
Bench Test Procedure For A TH48FT - E70 Oil Field Transmission {3030} Bench Test Procedure For A TH48FT - E70 Oil Field Transmission {3030}
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil - Change
TA19-M2WD and TA19-M4WD Agricultural Transmissions Breather (Transmission) - Clean
TA19-M2WD and TA19-M4WD Agricultural Transmissions Capacities (Refill)
TA19-M2WD and TA19-M4WD Agricultural Transmissions Lifting and Tying Down the Transmission
C280-6 and C280-8 Engines Exhaust Manifold - Remove and Install - C280-8
C280-6 and C280-8 Engines Exhaust Manifold - Remove and Install - C280-6
C280-12 and C280–16 Marine Engines Exhaust Manifold - Remove and Install - C280-16
C280-12 and C280–16 Marine Engines Exhaust Manifold - Remove and Install - C280-12
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Control
3512C and 3516C Marine Auxiliary and Generator Set Engines Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
C0.5 and C0.7 Industrial Engines Fuel Injector - Test/Change
2006/11/13 New Software is Now Available for EMCP 3.1, EMCP 3.2, and EMCP 3.3 {4490, 7620}
2006/10/16 New Software Available for Product Link {7606, 7620}
C280-12 and C280–16 Marine Engines Engine Lifting Bracket - Remove and Install
TA19-M2WD and TA19-M4WD Agricultural Transmissions Maintenance Interval Schedule
C280-6 and C280-8 Engines Engine Lifting Bracket - Remove and Install
C0.5 and C0.7 Industrial Engines Cooling System Water Temperature Regulator - Replace
TH48-E70-C27I, TH48-E70-C32I and TH48-E70-C32P Petroleum Power Train packages and TH48-E70 Petroleum Transmission Power Train Electronic Control System Starting System
CAESultra Installation for Wheel Loaders, Wheel Dozers, Landfill Compactors, and Motor Graders {7604, 7620} CAESultra Installation for Wheel Loaders, Wheel Dozers, Landfill Compactors, and Motor Graders {7604, 7620}
3508C, 3512C and 3516C Marine Engines Flywheel Housing - Remove
2014/08/08 New Cylinder Head Groups Are Used For Certain 3500 Engines {1100}
3508C, 3512C and 3516C Marine Engines Flywheel Housing - Install