Crankshaft - Type 1
Show/hide table
图 1 | g01676750 |
Show/hide table
318-3128 曲轴总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
-     | -     | -     | 新曲轴的端隙为 0.17 至 0.63 mm (0.007 至 0.025 in)。     |
注释:将曲轴组装到缸体中之前,先用清洁的发动机机油润滑主轴承轴颈。 | |||
注释:止推垫片应只用在后主轴承上。 | |||
A     | 1     | 146-3173 定位销     | 延伸长度为 9.0 ± 0.5 mm (0.35 ± 0.02 in)。     |
1 | 286-5311 定位销     | ||
1     | -     | -     | 有关连杆轴承轴颈和连杆轴承的信息,请参阅技术规格, "连杆轴承轴颈"。     |
2     | -     | -     | 有关主轴承轴颈和主轴承的更多信息,请参阅技术规格, "主轴承轴颈"。     |
Show/hide table
图 2 | g01473592 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     |
3     | 8     | 2W-2288 螺塞     | 拧紧扭矩至 50 ± 7 N·m (37 ± 5 lb ft)。     |
4     | 34     | 237-8306 螺栓组件     | 使用以下步骤拧紧螺栓 (4) : 注释:请勿重复使用配重螺栓。 均匀地拧紧配重螺栓。 1. 用 6V-4876 润滑剂 润滑螺栓的螺纹、柄部、螺栓头下的接触面和垫片。 2. 拧紧扭矩至 220 ± 20 N·m (162 ± 15 lb ft)。 3. 将各螺栓再次拧紧扭矩至 90 ± 5 度。     |
D     | 14     | 095-0893 弹簧销     | 最大延伸长度为 8 mm (0.3 in)。     |
Show/hide table
图 3 | g01473613 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     |
G     | 1     | 345-8567 定位销     | 定位销的延伸长度为 10.0 ± 0.5 mm (0.39 ± 0.02 in)。     |
Caterpillar Information System:
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Current Transformer (Inverter Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fuse Switch
G3508, G3512 and G3516 Engines Camshaft - Install
G3508, G3512 and G3516 Engines Camshaft - Remove
120M, 12M, 140M and 160M Motor Graders Drive Chain - Check
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys System Fuse (Inverter Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Digital Gate Logic PWA
Troubleshooting the Flywheel Housing for Failures of the Bolts{1157, 1157} Troubleshooting the Flywheel Housing for Failures of the Bolts{1157, 1157}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Inverter Module
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Internal Component Preremoval Steps (Inverter Cabinet)
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 3823 - FMI 16
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 3824 - FMI 6
Reset the Real Time Clock After Maintenance for On-Highway Truck Engines{1900, 1901} Reset the Real Time Clock After Maintenance for On-Highway Truck Engines{1900, 1901}
2006/06/01 Improved Seal on Filters {1308}
Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542} Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Diode Rectifier
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys General Purpose Interface PWA (Inverter Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Inverter Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Transformer (T7)
Set and Test the Overspeed Verification Switch{7410, 7427, 7490} Set and Test the Overspeed Verification Switch{7410, 7427, 7490}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fan (Inverter Cabinet)
C4.4 Industrial Engine Connecting Rod - Inspect
C175-16 Locomotive Engine Connecting Rod and Main Bearing Journals
C175-16 Locomotive Engine Crankshaft Wear Sleeves and Seals