Exhaust Elbow - Remove and Install
Removal Procedure
- If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
- Loosen clamp assemblies (1) , (3) and (5) .
Note: Mark the orientation of clamp assembly (3) prior to removal.
Show/hide table
Illustration 1 | g02331933 |
- Slide elbow (2) into bellows (4) in order to gain clearance. Remove the bellows assembly.
Installation Procedure
- If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
- Distance (X) is 40 mm (1.6 inch). Place Mark (B) onto elbow (2) . a Distance (X) from the end of elbow (2) .
Show/hide table
Illustration 2 | g02095400 |
Show/hide table
Illustration 3 | g02332313 |
Alignment wrap (A) is not shown for photographic purposes. Typical Example |
Note: Alignment wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows.
Note: The alignment wrap (A) should not be removed until Step 11. Bellows (4) should never be flexed during installation.
- Insert elbow (2) into the bellows. The elbow should be inserted as far as possible without using force. This action will minimize the overall length of the bellows assembly and will help with installation.
- Prior to installation, position both ball clamp assemblies (1) and (5) onto the bellows assembly.
Show/hide table
Illustration 4 | g02331933 |
Alignment wrap (A) is not shown for photographic purposes. |
Show/hide table
Illustration 5 | g02097701 |
The photo is a cutaway view of the ball clamp assembly which is located near the combustion head group. |
Show/hide table
Illustration 6 | g02098533 |
The photo is a cutaway view of the ball clamp assembly. |
- Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (2) in the slip joint at clamp assembly (3) in order to position the bellows assembly.
- Verify that the cup of the ball joint (E) does not touch the radius of the ball (D) . Position ball clamp (1) and hand tighten ball clamp (1) . Measure Distance (Y) and Distance (Z) . The two measurements should be equal. Repeat the measurements every 90° around ball clamp (1) . If necessary, adjust ball clamp (1) .
- Repeat Step 6 for ball clamp (5) which is located near the turbocharger.
- Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (3) .
- Torque ball clamp (1) to a torque of 35 ± 2 N·m (26 ± 1 lb ft).
Note: Do not use power tools in order to torque clamp assemblies (1) , (3) , and (5) .
- Torque ball clamp (5) to a torque of 35 ± 2 N·m (26 ± 1 lb ft).
- Remove alignment wrap (A) from bellows (4) .
- Torque clamp assembly (3) to a torque of 55 ± 8 N·m (41 ± 6 lb ft).
Caterpillar Information System:
D8T, D9T and D11T Track-Type Tractors Monitoring System Warning Operation
966K Wheel Loader and 972K Wheel Loader Braking and Hydraulic Fan System Parking Brake Actuator - Adjust
854K Wheel Dozer and 992K Wheel Loader Engine to Torque Converter - Connect
980K Wheel Loader Braking and Hydraulic Fan System Parking Brake - Test
C15 and C18 Tier 4 Final Engines Electronic Unit Injector - Adjust
966K Wheel Loader and 972K Wheel Loader Braking and Hydraulic Fan System Brake System Air - Purge
966K XE Wheel Loader C9.3 Engine Supplement Clean Emissions Module - Remove and Install
953D Track-Type Loader Mirror
953D Track-Type Loader Visibility Information
953D Track-Type Loader Slope Operation
Bench Test Procedure for a D6T and D6R Track-Type Tractor and PL72 Pipelayer Transmission{3030, 3073} Bench Test Procedure for a D6T and D6R Track-Type Tractor and PL72 Pipelayer Transmission{3030, 3073}
980K Wheel Loader Braking and Hydraulic Fan System Service Brakes - Test
966K Wheel Loader and 972K Wheel Loader Braking and Hydraulic Fan System Brake Accumulator - Test and Charge
C13 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install
336E Excavator Machine System Specifications Stick Cylinder Lines
953D Welding Tractor Belt - Inspect/Replace
953D Welding Tractor Drive Shaft - Lubricate
C13 Engines for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
D8T, D9T and D11T Track-Type Tractors Monitoring System Menu Navigation
994H Wheel Loader Electrohydraulic System Main Control Valve - Left Side
Rework Procedure for the Improved Ride Control Lines Group{5004, 5057, 5057} Rework Procedure for the Improved Ride Control Lines Group{5004, 5057, 5057}
C13 Tier 4 Final Engines Idler Pulley
C13 Engines for Caterpillar Built Machines Electric Starting Motor
330F MHPU Mobile Hydraulic Power Unit Machine System Hoist Solenoid Valve - Boom Lowering