Final Drive
Show/hide table
 | |
| 图 1 | g02641436 |
Show/hide table
| 324-2343 终传动总成 和 343-5375 终传动总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 80 | 1D-4643 螺栓 | 拧紧至扭矩为 1150 ± 150 N·m (848 ± 111 lb ft)。 |
| 2 | 35 | 7X-0408 螺栓 | 拧紧至扭矩为 1050 ± 150 N·m (774 ± 111 lb ft)。 |
| 3 | 16 | 030-7335 锁紧螺栓 | 拧紧至扭矩为 240 ± 40 N·m (177 ± 30 lb ft)。 |
| 4 | 1 | 124-2377 唇形密封 | 用润滑剂稍微润滑即将密封的密封唇。 |
| 5 | 1 | 172-5093 双锥面密封件总成 | 装配时，橡胶曲面密封件必须清洁干燥，且与橡胶曲面密封件接触的所有表面也必须清洁干燥。 在接触橡胶曲面密封件的金属密封件表面上涂抹薄薄的油层，然后立即安装。 必须将密封件装配得与孔平齐。 橡胶曲面密封件不得有凸起，且这些密封件也不得扭曲。 |
| A | - | - | 保持 0.08 ± 0.05 mm (0.003 ± 0.002 in) 的间隙以确保轴和挡圈之间的金属夹紧。 在用螺栓将挡圈安装到轴上之前检查此间隙。 用螺栓拧紧挡圈后，确保齿轮能自由转动。 如果齿轮不能自由转动，用适当的工具将挡圈向托架方向冲压。 |
| B | - | - | 保持 0.08 ± 0.05 mm (0.003 ± 0.002 in) 的间隙以确保装配期间心轴和挡圈之间的金属夹紧。 |
| 6 | 1 | 110-2653 衬套 | 内径为 103.25 ± 0.08 mm (4.065 ± 0.003 in)。 |
| 7 | 32 | 7T-1243 螺栓 | 将Loctite C5-A 铜防咬合剂或等同物涂覆到螺纹上。 将链轮段螺栓拧紧至扭矩为 870 ± 70 N·m (642 ± 52 lb ft)。 |
| 在达到该扭矩后，应该再将这些螺栓拧紧120 ± 5 度。 转动后的最小扭矩为 2030 N·m (1497 lb ft)。 |
|||
| 8 | 16 | 030-7335 锁紧螺栓 | 拧紧至扭矩为 270 ± 40 N·m (199 ± 30 lb ft)。 |
Show/hide table
 | |
| 图 2 | g02790589 |
Show/hide table
| 324-2343 终传动总成 和 343-5375 终传动总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 9 | 1 | 6V-3298 磁性塞 | 拧紧至扭矩为 225 ± 20 N·m (166 ± 15 lb ft)。 |
| 10 | 1 | 9S-4185 O 形密封圈塞 | 拧紧至扭矩为 80 ± 8 N·m (59 ± 6 lb ft)。 |
Caterpillar Information System:
993K Wheel Loader Tilt Cylinder Cap Weld Rework Procedure{0679, 5104} 993K Wheel Loader Tilt Cylinder Cap Weld Rework Procedure{0679, 5104}
C13, C15, and C18 Tier 4 Final Engines Flywheel Housing
D11R Track-Type Tractor Maintenance Interval Schedule
D9T Track-Type Tractor Lubricant Viscosities - Fluids Recommendations
Installation of 11SU (S/N: 8PP) and 11U (S/N: 8RP) Bulldozer with Dual Tilt Cylinder {6050} Installation of 11SU (S/N: 8PP) and 11U (S/N: 8RP) Bulldozer with Dual Tilt Cylinder {6050}
950K Wheel Loader and 962K Wheel Loader Machine Systems Position Sensor (Throttle)
D11R Track-Type Tractor Lubricant Viscosities - Fluids Recommendations
950K Wheel Loader and 962K Wheel Loader Machine Systems Governor Pedal
330F MHPU Mobile Hydraulic Power Unit Machine System Cab
Procedure to Machine Damaged Transmission and Differential Yokes {3030, 3253, 3258} Procedure to Machine Damaged Transmission and Differential Yokes {3030, 3253, 3258}
950K Wheel Loader and 962K Wheel Loader Machine Systems Window Wiper and Wiper Motor
966K Wheel Loader and 972K Wheel Loader Machine Systems Toggle Switch (Ground Level Shutdown)
994H Wheel Loader Electrohydraulic System Relief Valve - Implement
C13 Engines for Caterpillar Built Machines Engine Support (Front)
D11T Track-Type Tractor Machine Systems Case and Frame
2010/12/16 Procedure to Rework the Parking Brake Oil Pressure Switch on Certain AD30, AD45B, AD55, and AD55B Underground Articulated Trucks {1408, 1435}
320E and 323E Excavators Machine System Specifications Control Valve (Auxiliary)
C4.4 Industrial Engine Clean Emissions Module
854K Wheel Dozer and 992K Wheel Loader Engine from Torque Converter - Separate
966K Wheel Loader and 972K Wheel Loader Braking and Hydraulic Fan System Service Brake System Pressure - Test
C13 Engines for Caterpillar Built Machines Idler Pulley
966K XE Wheel Loader Machine Systems Pilot Oil Accumulator (Dead Engine Lower) - Remove and Install
D6N Track-Type Tractor Additional Messages
980K Wheel Loader Braking and Hydraulic Fan System Service Brakes - Test