Window Wiper and Wiper Motor
Show/hide table
 | |
| Illustration 1 | g03067556 |
Front view | |
Show/hide table
| Specification for 279-0228 Window Wiper Gp | |||
| Item | Qty | Part | Specification Description |
| A | 1 | 6V-5851 Wiper Blade | The distance of the front wiper blade from the glass edge of the window in the park position is 210.0 ± 3.0 mm (8.27 ± 0.12 inch). |
| Note : By using a wire with the diameter of 0.5 mm (0.02 inch), adjust the jets of the nozzle assembly to direct spray onto the glass directly in front of the front wiper blade. |
|||
| 1 | 1 | 373-2414 Window Wiper Arm Gp | Tension of the front window arm group in the loaded position is 15.0 ± 0.5 N (3.4 ± 0.1 lb). |
| B | Angle for the front window arm group from the automatic park position is 64 degrees. | ||
| 2 | 4 | 8T-5400 Connector As | Torque to 0.35 ± 0.05 N·m (3.10 ± 0.44 lb in). |
Show/hide table
 | |
| Illustration 2 | g03067837 |
View C-C | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 3 | 2 | - | Tighten the nut to 38 ± 2 N·m (28 ± 1 lb ft). |
| 4 | 2 | - | Tighten the nut to 13 ± 2 N·m (115 ± 18 lb in). |
| 5 | 2 | - | Tighten the nut to 38 ± 2 N·m (28 ± 1 lb ft). |
| 6 | 4 | - | Tighten the nut to 14 ± 2 N·m (124 ± 18 lb in). |
Show/hide table
 | |
| Illustration 3 | g03068896 |
Rear view | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 7 | 1 | 152-6641 Window Wiper Arm As | Tension of the rear window wiper arm assembly in the loaded position is 5.0 ± 0.5 N (1.1 ± 0.1 lb). |
| E | Angle for the rear window wiper arm assembly from the automatic park position is 110 degrees. | ||
| F | 1 | 6V-5851 Wiper Blade | The distance of the rear wiper blade from the glass edge of the window in the park position is 75.0 ± 3.0 mm (2.95 ± 0.12 inch). |
| Note : By using a wire with the diameter of 0.5 mm (0.02 inch), adjust the jets of the nozzle assembly to direct spray onto the glass directly. |
Show/hide table
 | |
| Illustration 4 | g03069001 |
View D-D | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 8 | - | - | Use the following procedure in order to tighten the nuts of the rear window wiper arm group: |
| 1. Tighten the nuts of the window wiper arm assembly to 21 ± 1 N·m (186 ± 9 lb in). |
|||
| 2. After a minimum of 0.5 hours, again tighten the nuts of the window wiper arm assembly to 21 ± 1 N·m (186 ± 9 lb in). |
|||
| Note : Ensure the minimum field torque for the nut (8) of the wiper arm assembly is 12 N·m (106 lb in). |
|||
| 9 | - | - | Tighten the nut to 9 ± 1 N·m (80 ± 9 lb in). |
| 10 | - | - | Tighten the nut to 7.5 ± 0.5 N·m (66.4 ± 4.4 lb in). |
Caterpillar Information System:
966K Wheel Loader and 972K Wheel Loader Machine Systems Toggle Switch (Ground Level Shutdown)
966K Wheel Loader and 972K Wheel Loader Machine Systems Toggle Switch (Power Guard Actuator)
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
D11T Track-Type Tractor Power Train Pivot Shaft Lubrication Group
966K Wheel Loader and 972K Wheel Loader Machine Systems Power Guard Actuator
C13 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
D11T Track-Type Tractor Power Train Track Roller Frame
Rework Procedure for the 902/906/908 Rear Axle Pinion Shaft{0645, 3254, 3256, 3258, 3260, 7561} Rework Procedure for the 902/906/908 Rear Axle Pinion Shaft{0645, 3254, 3256, 3258, 3260, 7561}
2010/12/06 New Implement Valve Centering Springs And Retainers Are Now Used On Certain Track-Type Tractors {5051, 5051}
Cat® Grade Control for Wheel Tractor Scrapers Glossary
C7 Engines for IT62H Integrated Toolcarrier and for 950H and 962H Wheel Loaders E1172 Engine Idle Shutdown Pending
C7 Engines for IT62H Integrated Toolcarrier and for 950H and 962H Wheel Loaders E1171 Engine Idle Shutdown Occurred
Procedure to Machine Damaged Transmission and Differential Yokes {3030, 3253, 3258} Procedure to Machine Damaged Transmission and Differential Yokes {3030, 3253, 3258}
330F MHPU Mobile Hydraulic Power Unit Machine System Cab
950K Wheel Loader and 962K Wheel Loader Machine Systems Governor Pedal
D11R Track-Type Tractor Lubricant Viscosities - Fluids Recommendations
950K Wheel Loader and 962K Wheel Loader Machine Systems Position Sensor (Throttle)
Installation of 11SU (S/N: 8PP) and 11U (S/N: 8RP) Bulldozer with Dual Tilt Cylinder {6050} Installation of 11SU (S/N: 8PP) and 11U (S/N: 8RP) Bulldozer with Dual Tilt Cylinder {6050}
D9T Track-Type Tractor Lubricant Viscosities - Fluids Recommendations
D11R Track-Type Tractor Maintenance Interval Schedule
C13, C15, and C18 Tier 4 Final Engines Flywheel Housing
993K Wheel Loader Tilt Cylinder Cap Weld Rework Procedure{0679, 5104} 993K Wheel Loader Tilt Cylinder Cap Weld Rework Procedure{0679, 5104}
D11R Track-Type Tractor Power Train Final Drive
994H Wheel Loader Electrohydraulic System Relief Valve - Implement