Check and Relief Valve (Main Hydraulic) - Remove
Removal Procedure
Note: Cap all hydraulic lines and fittings that are disconnected in order to prevent oil loss. This will also keep contaminants out of the hydraulic system.
Rear Check and Relief Valves
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-1114 | Vacuum Cap | 1 |
- Install Tooling (A) onto the hydraulic oil tank for the implement system.
Show/hide table
 | |
| Illustration 1 | g01421619 |
- The rear check and relief valve assembly is located on each side of the machine near the rod end of the steering cylinders. Disconnect hose assemblies (1) and (2) .
Show/hide table
 | |
| Illustration 2 | g01428829 |
- Disconnect hose assembly (3) from the inside of the check and relief valve assembly.
Show/hide table
 | |
| Illustration 3 | g01428830 |
- Remove bolts (4) and remove the check and relief valve assembly (5). Repeat for the other side.
Show/hide table
 | |
| Illustration 4 | g01428832 |
Front Check and Relief Valves
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-1114 | Vacuum Cap | 1 |
- Install Tooling (A) onto the hydraulic oil tank for the implement system.
Show/hide table
| | |
| Illustration 5 | g01421619 |
- The front check and relief valve assembly is located on each side of the machine above the front drive shaft. Disconnect hose assemblies (1) and (2) .
Show/hide table
 | |
| Illustration 6 | g01428894 |
- Disconnect hose assemblies (3) from the front and the back of the front check and relief valve assembly.
Show/hide table
 | |
| Illustration 7 | g01428895 |
- Remove bolts (4) and remove the front check and relief valve assembly (5) .
Show/hide table
 | |
| Illustration 8 | g01428897 |
Caterpillar Information System:
374F Excavator Joystick Controls Alternate Patterns
938H Wheel Loader and IT38H Integrated Toolcarrier Power Train Position Sensor (Articulation Angle) - Adjust and Calibrate
993K Wheel Loader Power Train Torque Converter (Lockup)
D6T Track-Type Tractor Machine Systems Radiator Guard and Support
D6 Track Type Tractor Machine Systems Toggle Switch (Ground Level Shutdown)
854K Wheel Dozer and 992K Wheel Loader Electric Starting Motor - Remove and Install
319D Excavator Hydraulic System Main Hydraulic Pump Air - Purge
993K Wheel Loader Steering Frame Lock
2007/12/24 New Hoses and Hose Routing for the Steering Cylinder on the Right Side is Now Used {4304}
2007/12/10 New Design Improves Air Conditioning Lines {1808, 7320}
2007/12/24 An Improved Clamp is Now Used On Coolant Lines {1380}
D6T Track-Type Tractor Machine Systems Case and Frame
312D2 and 313D2 Excavators Bucket Linkage - Lubricate
854K Wheel Dozer and 992K Wheel Loader Engine from Torque Converter - Separate
2007/11/05 An Improved Seal For The Standard Final Drive Is Now Available {4050, 7561}
2007/12/31 Improvements for the Torque Converter {3101}
2007/11/05 A New Rear Hood Assembly is Available for Improved Durability {7251}
994F Wheel Loader Machine Systems Check and Relief Valve (Main Hydraulic) - Install
2007/11/05 Troubleshooting Procedure for the Engine Speed Sensor on Small Track-Type Tractors {1907}
Salvage of Final Drive Sprocket Hubs For Pipelayers, Track Loaders, and Track-Type Tractors {4050, 4184} Salvage of Final Drive Sprocket Hubs For Pipelayers, Track Loaders, and Track-Type Tractors {4050, 4184}
854K Wheel Dozer and 992K Wheel Loader Engine to Torque Converter - Connect
2007/10/29 Rework Procedure for the Brackets of the Air Cleaner on Wheel Loaders {1051}
2007/11/05 The Parking Brake Group is Updated {4267}
Procedure to Install the New Lower Hitch Group on the 525C, 535C, and 545C Wheel Skidders{7057, 7100} Procedure to Install the New Lower Hitch Group on the 525C, 535C, and 545C Wheel Skidders{7057, 7100}