Installation of Speed Sensor Group{1907}
- Engine:
- 3406E (S/N: 5EK1-30869)
Introduction
This Special Instruction provides instructions for the installation of the 265-9033 Speed Sensor Group on certain 3406E Engines.
Note: This Special Instruction should only be used for 3406E Engines. The 265-9033 Speed Sensor Gp is used on other engine models. The 3406E is the only model that uses the 126-8481 Washer . Do not perform any procedure that is outlined in this Special Instruction until the information is read and understood.
Installation
Use the following procedure to install the engine speed sensor:
- Place two 126-8481 Washers over the threads and the O-ring of the 265-9033 Speed Sensor Gp .
Note: A 126-8481 Washer may be stuck to the housing. Ensure that only two washers are on the engine after the installation.
- Install the 265-9033 Speed Sensor Gp onto the engine.
Show/hide table
Illustration 1 | g01247702 |
126-8481 Washer |
- Torque the sensor to 40 ± 5 N·m (29.5 ± 3.7 lb ft).
- Connect the pigtail to the harness.
- Clear all the following faults from the event log: speed and timing.
- Follow the proper procedure for Engine Timing in order to calibrate.
Caterpillar Information System:
2006/03/06 A Piston Ring Compressor is Available for C175 Engines {0701, 0705, 1215}
2006/03/13 A New Piston and Rod Gp has been Released {1225}
CX31 On-Highway Transmission Transmission Oil Supply
C18 Marine and Marine Generator Set Engines Auxiliary Water Pump
C175 Generator Sets Speed Sensor - Clean/Inspect
Installation Instructions for New Variable Valve Actuator (VVA) Pressure Sensor{5078, 5078} Installation Instructions for New Variable Valve Actuator (VVA) Pressure Sensor{5078, 5078}
2006/04/03 Spanner Wrench is Available for Servicing the Air Starting Motor {0700, 0710, 1451}
C18 Marine and Marine Generator Set Engines Engine Oil Pan
C9 Industrial Engines Valve Mechanism Cover
CX31 On-Highway Transmission Power Train Pressures
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head Valves
G3500 A3 Engines Air/Fuel Ratio Control - Oxygen Feedback
2006/03/27 New Infrared Thermometer Has Narrow, 50:1 Target Ratio, Wide Temperature Range {0776, 1350, 3000, 4000, 4150, 4250}
TH31-E61 and TH35-E81 Petroleum Transmissions Plate Locations and Film Locations
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Electronic Control Unit
CX31 On-Highway Transmission Retarder - Test
G3500 A3 Engines Electrical Power Supply
C15 and C18 Engines for Caterpillar Built Machines E363 High Fuel Supply Temperature
AccuGrade® GPS (CD700) Electrical Connector - Inspect
G3500 A3 Engines Detonation Sensor
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Diagnostic Trouble Code List
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Event Code List
C13, C15, and C18 Generator Set Engines Vibration Damper and Pulley
C13, C15, and C18 Generator Set Engines Vibration Damper and Pulley