C27 and C32 Engines for Caterpillar Built Machines Caterpillar

Cylinder Head Valves

Usage:

854K 221

Show/hide table




Ilustrasi 1	g03347670
Contoh khusus

Show/hide table

Tabel 1
Spesifikasi untuk 284-8892 Group Cylinder Head dan 359-0936 Group Cylinder Head
Item	Jml	Suku Cadang	Keterangan Spesifikasi
1	24	247-9908 Pegas	Panjang pada gaya uji adalah 67.12 mm (2.643 inch). Gaya uji adalah 320 ± 25 N (71.9 ± 5.6 lb). Panjang bebas setelah pengujian sekitar 76.70 mm (3.020 inch).
2	24	211-3122 Pegas	Panjang pada gaya uji adalah 60.14 mm (2.368 inch). Gaya uji adalah 150 ± 12 N (33.7 ± 2.7 lb). Panjang bebas setelah pengujian sekitar 71.70 mm (2.823 inch).
3	24	122-7375 Pengarah Katup	Tinggi (A) hingga langkah yang berada di pengarah katup 35.0 ± 0.5 mm (1.38 ± 0.02 inch). Sebelum pemasangan, lubang pada pengarah katup memiliki diameter 9.502 ± 0.013 mm (0.3741 ± 0.0005 inch).
Lumasi diameter dalam pengarah katup dengan oli engine yang bersih 1E1867B segera sebelum pemasangan katup di silinder.
4	12	153-7024 Katup Buang	Sudut muka berkisar 45,75 ± 0,25 derajat. Diameter batang 9.441 ± 0.010 mm (0.37169 ± 0.00039 inch). Diameter kepala katup 41.81 ± 0.13 mm (1.646 ± 0.005 inch).
5	12	153-7023 Katup Saluran Masuk	Sudut muka berkisar 60,75 ± 0,25 derajat. Diameter batang 9.441 ± 0.010 mm (0.37169 ± 0.00039 inch). Diameter kepala katup 47.00 ± 0.13 mm (1.850 ± 0.005 inch).
Susutkan sisipan dudukan katup dengan mengurangi temperaturnya. Menyusutkan sisipan dudukan katup memungkinkan pemasangan ke counterbore.
6	12	226-5561 Sisipan Dudukan Katup	Sudut muka sisipan dudukan katup berkisar 45,25 ± 0,25 derajat. Diameter luar 42.840 ± 0.013 mm (1.6866 ± 0.0005 inch). Lubang cylinder head memiliki kedalaman 13.90 ± 0.05 mm (0.547 ± 0.002 inch). Lubang cylinder head memiliki diameter 42.774 ± 0.025 mm (1.6840 ± 0.0010 inch).
7	12	224-3983 Sisipan Dudukan	Sudut muka sisipan dudukan katup berkisar 30,25 ± 0,25 derajat. Diameter luar 48.025 ± 0.013 mm (1.8907 ± 0.0005 inch). Lubang cylinder head memiliki kedalaman 14.00 ± 0.05 mm (0.551 ± 0.002 inch). Lubang cylinder head memiliki diameter 47.950 ± 0.025 mm (1.8878 ± 0.0010 inch).

Caterpillar Information System:

G3500 A3 Engines Air/Fuel Ratio Control - Oxygen Feedback

2006/02/20 Installation of a Spring in the Oil Filter Bypass Valve on Certain Applications {1306}

G3500 A3 Engines Carburetor

G3500 A3 Engines Location of Components

2006/03/13 The Heater and Air Conditioner Fan Motor has been Enhanced to Improve Motor Life {5927, 7304, 7320}

C18 Marine and Marine Generator Set Engines Engine Oil Filter Base

Update of Parameters for Throttle Inputs During Commissioning Procedure{1901, 4490} Update of Parameters for Throttle Inputs During Commissioning Procedure{1901, 4490}

C175 Generator Sets Fuel System Secondary Filter - Replace

G3500 A3 Engines Ignition System

C27 and C32 Engines for Caterpillar Built Machines Fuel Transfer Pump

C18 Marine Auxiliary and Marine Generator Set Engines Engine Oil Filter Base

CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 158 - FMI 2

CX31 On-Highway Transmission Power Train Pressures

C9 Industrial Engines Valve Mechanism Cover

C18 Marine and Marine Generator Set Engines Engine Oil Pan

2006/04/03 Spanner Wrench is Available for Servicing the Air Starting Motor {0700, 0710, 1451}

Installation Instructions for New Variable Valve Actuator (VVA) Pressure Sensor{5078, 5078} Installation Instructions for New Variable Valve Actuator (VVA) Pressure Sensor{5078, 5078}

C175 Generator Sets Speed Sensor - Clean/Inspect

C18 Marine and Marine Generator Set Engines Auxiliary Water Pump

CX31 On-Highway Transmission Transmission Oil Supply

2006/03/13 A New Piston and Rod Gp has been Released {1225}

2006/03/06 A Piston Ring Compressor is Available for C175 Engines {0701, 0705, 1215}

Installation of Speed Sensor Group{1907} Installation of Speed Sensor Group{1907}

2006/03/27 New Infrared Thermometer Has Narrow, 50:1 Target Ratio, Wide Temperature Range {0776, 1350, 3000, 4000, 4150, 4250}