Water Temperature Regulator - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将冷却液从冷却系统中排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 断开冷却液温度传感器的线束组件 (5) 。
Show/hide table
图 1 | g01238605 |
- 将软管 (2) 从壳体歧管 (3) 上断开。
- 将软管组件 (1) 从水温调节器壳体 (4) 上断开。
- 拆下螺栓 (7) 。 拆下管 (6) 、水温调节器壳体 (4) 和壳体歧管 (3) 。
- 将水温调节器壳体 (4) 从壳体歧管 (3) 上拆下。 将 O 形密封圈 (9) 和 (8) 从壳体歧管 (3) 上拆下。
Show/hide table
图 2 | g01238792 |
- 拆下水温调节器 (10) 。
- 拆下唇型密封 (12) 。
- 将管 (6) 从水温调节器壳体 (4) 上拆下。 拆下 O 形密封圈 (11) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 221-8647     | 密封安装工具总成     | 1     |
B     | 1U-6396     | O 形密封圈组件固定胶     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将唇形密封 (12) 安装到水温调节器壳体 (4) 中。
Show/hide table
图 3 | g01238792 |
- 将 O 形密封圈 (11) 安装到管 (6) 上。 将工具 (B) 涂抹在 O 形密封圈上。 将管安装在水温调节器壳体上。
- 将 O 形密封圈 (8) 和 (9) 安装在壳体歧管 (3) 上。
- 将水温调节器壳体 (10) 安装在壳体歧管 (3) 上。
- 将管 (6) 安装在水温调节器壳体 (4) 上。 安置水温调节器壳体 (4) 和壳体歧管 (3) 并安装螺栓 (7) 。
Show/hide table
图 4 | g01238605 |
- 连接软管组件 (1) 和软管 (2) 。
- 连接冷却液温度传感器的线束组件 (5) 。
- 加注冷却系统。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Caterpillar Information System:
C15 and C18 Generator Set Engines Water Pump - Install
C280 Marine and Petroleum Engines Atmospheric Pressure Sensor
3500 Engines Aftercooler - Remove and Install
3500 Spark Ignited Engines Magneto Drive
C9 On-highway Engine Valve Mechanism Cover
3500 Engines Turbocharger - Install
C15 and C18 Generator Set Engines Water Pump - Remove
3500 Engines Turbocharger - Remove
C15 and C18 Generator Set Engines Engine Oil Pump - Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 177 - FMI 16
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 177 - FMI 4
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 177 - FMI 3
3512B and 3516B Engines Air Inlet Manifold - Remove and Install
3512E Petroleum Engines Air Inlet Manifold - Remove and Install
C4.4 (Mech) Industrial Engine Cooling System Coolant Level - Check
C15 and C18 Generator Set Engines Flywheel - Remove
C3.3 Industrial Engine Engine Oil Cooler - Inspect
C15 and C18 Generator Set Engines Flywheel Housing - Remove and Install
2006/02/06 New Kits Are Available to Repair Cracks and Threads in Ductile Iron {0676, 0685}
C280 Marine and Petroleum Engines Boost Pressure Sensor
C13, C15, and C18 Generator Set Engines Sensors and Electrical Connectors
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 740 - FMI 5
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 740 - FMI 6
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 734 - FMI 5