Programmable Parameters
Note: For an updated selection of the programmable parameters, refer to Special Instruction, REHS2884, "Application and Installation Guide".
Show/hide table
| Parameter | Available Range/Options | Default |
|---|---|---|
| Equipment Identification Parameters | ||
| Engine Serial Number | 18 characters | Not Programmed |
| Vehicle ID | 18 characters | Not Programmed |
| Transmission Serial Number | N/A | Factory Programmed |
| Torque Converter Serial Number | N/A | Factory Programmed |
| Transmission PTO Configuration Parameters | ||
| PTO Neutral Restriction | Disabled, Enabled | Disabled |
| PTO Mode Enable Status | Disabled or Enabled | Disabled |
| PTO Mode Gear Limit | Not Configured, Gear 1, Gear 2, Gear 3, Gear 4, Gear 5, Gear 6, Gear 7, Gear 8 | Not Configured |
| PTO Mode Maximum Engine Speed For Engagement | 0 - 5000 RPM | 0 |
| PTO Mode Maximum Engine Speed For Operation | 600 - 3500 RPM | 0 |
| PTO Mode Maximum Transmission Output Speed For Engagement | 0 - 8000 RPM | 0 |
| PTO Mode Maximum Transmission Output Speed for Operation | 0 - 8000 RPM | 0 |
| Driveline PTO Configuration Parameters | ||
| Driveline PTO Minimum Engine Speed for Latching | 500 - 3000 RPM | 0 |
| Driveline PTO Minimum Engine Speed for Torque Converter Lockup | 600 - 3000 RPM | 1000 |
| Driveline PTO Latching Enabled Status | Disabled, Enabled | Disabled |
| Driveline PTO Inertia Brake Enabled Status | Enabled, Disabled | Enabled |
| Driveline PTO Mode Enabled Gear Configuration | Disabled, Gear 1, Gear 2, Gear 3, Gear 4, Gear 5, Gear 6, Gear 7, Gear 8 | Disabled |
| Vehicle Configuration Parameters | ||
| Governed Engine Speed | 1800 - 3500 RPM | 2100 |
| Peak Torque Engine Speed | 1000 - 2500 RPM | 1200 |
| Transmission Output Shaft Torque Limit Configuration | 0 - 48336 lb-ft | 48336 |
| Auto Neutral Function Enabled Status | Disabled, Enabled | Disabled |
| Auto Neutral Gear Reengagement Brake Required Configuration | Not Required, Required | Not Required |
| Auto Neutral Gear Reengagement Configuration | Disabled, Enabled for Forward, Enabled for Forward and Reverse, Enabled for Reverse | Disabled |
| Maximum Transmission Output Speed to Enable Auto Neutral | 0 - 8000 RPM | 0 |
| Parking Brake Input Installation Status | Installed, Installed and Neutralizer Logic is Enabled, Not Installed | Installed |
| Neutral to Gear Inhibit Function Configuration | Disabled, Enabled for Forward, Enabled for Forward and Reverse, Enabled for Reverse | Disabled |
| Direction Inhibit Function Configuration | Disabled, Enabled for Forward, Enabled for Forward and Reverse, Enabled for Reverse | Disabled |
| Quick First Gear Limit Configuration | Disabled, Enable to First Gear and Do not lock out Reverse, Enabled to First Gear and Inhibit Shifts to Reverse | Disabled |
| Transmission Fail In Gear Enabled Status | Disabled, Enabled | Disabled |
| Shifter #1 Configuration | J1939, Not Installed, (PWM-Not Supported) | J1939 |
| Shifter #2 Configuration | J1939, Not Installed, (PWM-Not Supported) | Not Installed |
| Selected System Voltage | 12, 24 Volts | 0 |
| Transmission Default Shift Schedule Configuration | Economy 1, Economy 2, Performance 1, Performance 2 | Performance 1 |
| Transmission Default Maximum Gear Configuration | Disabled, Gear 1, Gear 2, Gear 3, Gear 4, Gear 5, Gear 6, Gear 7, Gear 8 | Disabled |
| Transmission Alternate Shift Schedule Configuration | Economy 1, Economy 2, Performance 1, Performance 2 | Economy 1 |
| Transmission Alternate Maximum Gear Configuration | Disabled, Gear 1, Gear 2, Gear 3, Gear 4, Gear 5, Gear 6, Gear 7, Gear 8 | Disabled |
| Minimum Start Gear Configuration | Gear 1, Gear 2 | Gear 1 |
| Transmission Calibration Configuration | Disabled, All Clutches | All Clutches |
| Retarder Configuration Parameters | ||
| Retarder Top Gear Limit Configuration | Disabled, Gear 1, Gear 2, Gear 3, Gear 4, Gear 5, Gear 6, Gear 7, Gear 8 | Disabled |
| Retarder Gear Limit Brake Input Enabled Status | Disabled, Enabled | Disabled |
| Transmission Retarder Installation Status | Not Installed, Installed | Not Installed |
| Input Selections | ||
| Service Brake Input Configuration | J1939 Body Controller, J1939 Cab Controller, J1939 Instrument Cluster, Switch Input | J1939 |
| Parking Brake Input Configuration | J1939 Body Controller, J1939 Cab Controller, J1939 Instrument Cluster, Not Configured, Switch to Ground | Switch to Ground |
| Economy Mode Input Configuration | J1939, Not Configured, Switch to Ground | Not Configured |
| Blank Shift Display Configuration | Disabled, Gear 1, Gear 2, Gear 3, Gear 4, Gear 5, Gear 6, Gear 7, Gear 8 | Disabled |
| Minimum Forward Start Gear Input Configuration (CX35 Only) | Mode Button Input, Switch Input | Switch to Ground |
| Quick Gear Limit Switch Configuration | Not Configured, Mode Button Input, Switch to Battery 1, Switch to Battery 2, Switch to Battery 3, Switch to Ground | Not Configured |
| Hold Function Input Configuration | Disabled, J1939, Switch to Ground | Disabled |
| Transmission Retarder Input Configuration | Dual Switch Input, J1939 Body Controller, J1939 Cab Controller, J1939 Instrument Cluster, PWM | PWM |
| Output Selections | ||
| Engine Running Starter Inhibit Enable Status | Disabled, Enabled | Enabled |
| Speed Enabled Output Configuration | Disabled, Engine Speed, PTO Engine Speed, Transmission Output Speed | Disabled |
| Speed Enabled output Turn On Speed | 0 - 5000 RPM | 0 |
| Speed Enabled Output Turn Off Speed | 0 - 8000 RPM | 0 |
| Gear Indicator Reverse Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator Neutral Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 8F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 7F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 6F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 5F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 4F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 3F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 2F Enabled Status | Disabled, Enabled | Disabled |
| Gear Indicator 1F Enabled Status | Disabled, Enabled | Disabled |
Caterpillar Information System:
C7 On-highway Engine Solenoid Valve
TH35 Well Servicing Transmissions Transmission and Torque Converter - Connect
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
3512C Petroleum Engines System Overview
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swivel - Install
2005/12/26 Operator Control Handle Mounting Change {3065, 5063, 5705}
320D and 323D Excavators Machine System Specifications Track Adjuster
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Motor - Install
C13 and C15 On-highway Engines Diesel Particulate Filter Collects Excessive Soot
2005/11/21 Improved Joint Assemblies and Seals are Used in the Compressor Bypass Group {1071}
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Additional Functions
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Cushion Valve - Install
3512C Petroleum Engines Override Switch
3512B Oil Well Servicing Engine (ADEM III) Fuel Position Multiplier
C175 Generator Set Engines Engine Oil Pan - Remove
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Bucket Linkage Bearings and Seals - Install
C13 and C15 On-highway Engines Intake Manifold Air Pressure Is Low
C7 Urban Transit Bus Engines Reference Material
CX31 On-Highway Transmission Torque Converter Housing
2005/12/19 New Piston and Rod Group {1225}
345D, 349D and 349D2 Excavator Machine System Specifications Fasteners
3512 Industrial Engine Exhaust Manifold
C27 and C32 Generator Set Engines Engine Oil Filter Base
325D and 329D Excavators and 325D Material Handler Machine System Specifications Bucket Adjuster