Track Carrier Roller - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 8T-5255     | 液压千斤顶     | 1     |
- 确保履带托链轮的轴和底盘机架组件上安装支架中的孔清洁并且没有灰尘。
- 由两人将履带托链轮定位到安装支架中。 履带托链轮的重量约为 43 kg (95 lb)。 调整托链轮,直到距离 (B) ,即安装支架外表面和托链轮之间的距离为 7.0 ± 0.5 mm (0.28 ± 0.02 in)。
Show/hide table
图 1 | g00489366 |
- 调整完履带托链轮 (2) 在安装支架内的位置后,拧紧螺栓 (1) 至扭矩为 1000 ± 125 N·m (738 ± 92 lb ft)。
Show/hide table
图 2 | g01200667 |
- 通过手动转动托链轮,确保托链轮 (2) 平滑转动。 使用工具 (A) 将履带组件慢慢降下至托链轮上。
Show/hide table
图 3 | g01200658 |
- 张紧履带的张力。 有关正确的步骤,请参阅操作和保养手册, "履带的调整 - 调整"。
Caterpillar Information System:
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Carrier Roller - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterbalance Valve (Travel) - Assemble
C15 Generator Set Engines Cat Data Link Circuit - Test
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterbalance Valve (Travel) - Disassemble
C175 Generator Set Engines Crankshaft Rear Seal - Install
C32 Petroleum Engines Engine Oil Filter Base - Install
3406C Engines for Caterpillar Built Machines Engine Oil Filter Base
C32 Petroleum Engines Engine Oil Filter Base - Remove
C175 Generator Set Engines Crankshaft Rear Seal - Remove
C175-16 and C175-20 Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Assemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove
C15 Generator Set Engines Speed Control (Switch) - Test
C11 and C13 Engines for Caterpillar Built Machines Low Engine Oil Pressure Lamp Circuit - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Mode Switch Setup
C6.6 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C175 Generator Set Engines Engine Oil Filter Housing - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Install
C6.6 Engines for Caterpillar Built Machines Power Sources
C7.1 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect