Track Carrier Roller - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 8T-5255     | 液压千斤顶     | 1     |
- 起动发动机。 把机器停放在坚硬的水平地面上。 关闭发动机。
- 松开张紧的履带。 请参阅操作和保养手册, "履带的调整 - 调整"。
Show/hide table
油脂和机油从安全阀中溢出可能导致人身伤亡。 处于高压下的油脂和机油从安全阀中溢出,可能渗透阀体。 不要通过安全阀来观察油脂是否溢出。 应通过履带或履带调节油缸查看履带是否松脱。 确保通风孔清洁,然后释放履带上的张紧力。 |
- 松开将履带托链轮 (2) 固定到底盘机架组件安装支架上的螺栓 (1) 。
Show/hide table
图 1 | g01200667 |
- 利用适当的垛架和工具 (A) 将履带吊离履带托链 (2) 。 拆下履带托链轮 (2) 。
Show/hide table
图 2 | g01200658 |
- 将履带组件吊离履带托链轮。 由两人拆下履带托链轮 (2) 。 履带托链轮 (2) 的重量为 43 kg (95 lb)。
Caterpillar Information System:
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterbalance Valve (Travel) - Assemble
C15 Generator Set Engines Cat Data Link Circuit - Test
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterbalance Valve (Travel) - Disassemble
C175 Generator Set Engines Crankshaft Rear Seal - Install
C32 Petroleum Engines Engine Oil Filter Base - Install
3406C Engines for Caterpillar Built Machines Engine Oil Filter Base
C32 Petroleum Engines Engine Oil Filter Base - Remove
C175 Generator Set Engines Crankshaft Rear Seal - Remove
C175-16 and C175-20 Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C6.6 Engines for Caterpillar Built Machines Electrical System
C7.1 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Carrier Roller - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Assemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil and Water Pump Drive - Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove
C15 Generator Set Engines Speed Control (Switch) - Test
C11 and C13 Engines for Caterpillar Built Machines Low Engine Oil Pressure Lamp Circuit - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Mode Switch Setup
C6.6 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C175 Generator Set Engines Engine Oil Filter Housing - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Install