Marine Transmission Oil Cooler - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the raw water system.
- Disconnect hose (1) and hose assemblies (3) from marine transmission oil cooler (2).
- Disconnect tube assemblies (5).
- Remove bolts (4) and marine transmission oil cooler (2).
Show/hide table
| |
| Illustration 1 | g01092716 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position marine transmission oil cooler (2) on the bracket assembly. Install bolts (4).
- Connect tube assemblies (5).
- Connect hose assemblies (3) and hose (1) to marine transmission oil cooler (2).
- Prime the raw water system.
Show/hide table
|
| |
| Illustration 2 | g01092716 |
Caterpillar Information System:
3500 Generator Sets Manual Stop Procedure
TH48-E80 Oil/Gas Transmission Transmission Planetary - Disassemble
TH48-E80 Oil/Gas Transmission Transmission Planetary - Assemble
C32 Petroleum Engines Crankshaft Rear Seal - Install
C32 Petroleum Engines Crankshaft Rear Seal - Remove
C27 and C32 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C18 Generator Sets Walk-Around Inspection
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
C32 Petroleum Engines Water Temperature Regulator - Remove and Install
Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319} Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319}
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Install
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Disassemble
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Assemble
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System Visual Inspection
C32 Marine and Auxiliary Marine Engines Flywheel Housing - Remove and Install
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Generator Installation
C18 Generator Sets Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C4.4 and C6.6 Engines for Caterpillar Built Machines Wastegate Solenoid - Test
C6.6 Industrial Engine Turbocharger
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1785 FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1785 FMI 04