Crankshaft Rear Seal - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-7600     | Slide Hammer Puller     | 1     |
B     | -     | Pry Bar     | 1     |
C     | 5P-7312     | Seal Distorter     | 1     |
D     | 5P-7314     | Distorter Ring     | 1     |
Start By:
- Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install two bolts from the flywheel and suitable washers through the rear gear in the crankshaft.
Note: Ensure that the rear gear remains in place when the crankshaft rear seal and crankshaft wear sleeve are removed.
- Use Tooling (B) to pry around the lip of crankshaft wear sleeve (2) .
Show/hide table
Illustration 1 | g01187206 |
Note: Ensure that you do not damage the flywheel housing with Tooling (B) .
Note: If the crankshaft wear sleeve starts to slide off the crankshaft, go to Step 3.
- Use Tooling (A) or a punch and hammer in order to puncture three or more holes in crankshaft rear seal (1) .
- Use Tooling (A) to remove crankshaft rear seal (1) .
- If necessary, use Tooling (C) and Tooling (D) to remove crankshaft wear sleeve (2) .
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C18 Generator Sets Walk-Around Inspection
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
C32 Petroleum Engines Water Temperature Regulator - Remove and Install
Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319} Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319}
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Install
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Remove
3126B Generator Set Engine CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C13 and C15 On-highway Engines ECM Memory - Test
C7 and C9 Marine Engines Engine Cranks but Will Not Start
G3500 Engines Model View Illustrations
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0700 - FMI 02
C32 Petroleum Engines Crankshaft Rear Seal - Install
TH48-E80 Oil/Gas Transmission Transmission Planetary - Assemble
TH48-E80 Oil/Gas Transmission Transmission Planetary - Disassemble
3500 Generator Sets Manual Stop Procedure
C32 Marine and Auxiliary Marine Engines Marine Transmission Oil Cooler - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Disassemble
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Assemble
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System Visual Inspection
C32 Marine and Auxiliary Marine Engines Flywheel Housing - Remove and Install
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Generator Installation