Flywheel Housing - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
B | - | Guide Stud 1/2 - 13 NC by 5 inch |
2 |
Start By:
- Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
- Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect tube assemblies (1) and (6).
- Remove brackets (2), (3), and (4) from flywheel housing (7).
- Attach a suitable lifting device to the transmission oil cooler. Remove bracket (5).
- Remove bolts (8) and install Tooling (B).
Show/hide table
Illustration 2 g01187390 - Attach Tooling (A) and a suitable lifting device to flywheel housing (7). The weight of flywheel housing (7) is approximately
98 kg (216 lb) . - Remove remaining bolts (8). Remove flywheel housing (7) and the gasket from the rear flywheel housing.
Show/hide table
Illustration 1 | g01187381 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
B | - | Guide Stud 1/2 - 13 NC by 5 inch |
2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (B) in the cylinder block.
- Attach Tooling (A) and a suitable lifting device to flywheel housing (7). The weight of flywheel housing (7) is approximately
98 kg (216 lb) . - Position the gasket and flywheel housing (7) on the rear flywheel housing. Install bolts (8).
- Remove Tooling (B) and install remaining bolts (8).
Show/hide table
Illustration 4 g01187414 - Tighten the bolts, as follows:
- In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of
135 ± 20 N·m (100 ± 15 lb ft) . - In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of
47 ± 9 N·m (35 ± 7 lb ft) .
Show/hide tableIllustration 5 g01187381 - In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of
- Connect tube assemblies (1) and (6).
- Install brackets (2), (3), (4), and (5).
Show/hide table
Illustration 3 | g01187390 |
End By:
- Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
- Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar Information System:
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System Visual Inspection
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Assemble
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Disassemble
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Remove
C32 Marine and Auxiliary Marine Engines Marine Transmission Oil Cooler - Remove and Install
3500 Generator Sets Manual Stop Procedure
TH48-E80 Oil/Gas Transmission Transmission Planetary - Disassemble
TH48-E80 Oil/Gas Transmission Transmission Planetary - Assemble
C32 Petroleum Engines Crankshaft Rear Seal - Install
C32 Petroleum Engines Crankshaft Rear Seal - Remove
C27 and C32 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Generator Installation
C18 Generator Sets Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C4.4 and C6.6 Engines for Caterpillar Built Machines Wastegate Solenoid - Test
C6.6 Industrial Engine Turbocharger
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1785 FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1785 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines PTO Switch Circuit - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1797 FMI 03
2005/08/15 Intake Valves are Sticking in Cold Climates {1100, 1105, 7620}
2005/08/01 Intake Valves are Sticking in Cold Climates {1105, 1130}
C9-XQ300 Rental Generator Set Product Lifting
2005/08/15 New Values for Runout for the Flywheel (Testing and Adjusting Manual) {1156}