Water Temperature Regulator - Remove and Install
Removal Procedure
- Drain the coolant from the cooling system into a suitable container for storage or disposal until the coolant is below the level of the water temperature regulator housing. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
- Remove bolts (2) from cover (1) .
Show/hide table
Illustration 1 | g01186856 |
- Remove cover (1). Remove O-ring seal (4) from cover (1). Remove water temperature regulators (5) from water temperature regulator housing (3) .
Show/hide table
Illustration 2 | g01186861 |
- If necessary, remove the lip seals.
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 221-8647     | Seal Installer Gp     | 1     |
- If necessary, use Tooling (A) to install the lip seals.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install water temperature regulators (5) in water temperature regulator housing (3) .
Show/hide table
Illustration 3 | g01186861 |
- Install new O-ring seal (4) in cover (1) .
- Position cover (1) on housing (3).
Show/hide table
Illustration 4 | g01186856 |
- Install bolts (2) .
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Caterpillar Information System:
Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319} Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319}
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Install
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Remove
3126B Generator Set Engine CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C13 and C15 On-highway Engines ECM Memory - Test
C7 and C9 Marine Engines Engine Cranks but Will Not Start
G3500 Engines Model View Illustrations
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0700 - FMI 02
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0590 - FMI 12
C7 and C9 On-Highway Engines Engine Rating Parameters
2005/07/01 A Improved Gasket is Now Available {1151, 1162}
Supplemental Parts and Service Information for the C18 Marine Propulsion Engine {1901, 7470} Supplemental Parts and Service Information for the C18 Marine Propulsion Engine {1901, 7470}
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
C18 Generator Sets Walk-Around Inspection
C27 and C32 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C32 Petroleum Engines Crankshaft Rear Seal - Remove
C32 Petroleum Engines Crankshaft Rear Seal - Install
TH48-E80 Oil/Gas Transmission Transmission Planetary - Assemble
TH48-E80 Oil/Gas Transmission Transmission Planetary - Disassemble
3500 Generator Sets Manual Stop Procedure
C32 Marine and Auxiliary Marine Engines Marine Transmission Oil Cooler - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Disassemble