Auxiliary Water Pump - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-1859 | Pliers | 1 |
C | 1P-1861 | Pliers | 1 |
E | 1P-0510 | Driver Group | 1 |
F | 9U-6956 | Installer | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (E) and a suitable press to install seal (15) in body (16).
Show/hide table
Illustration 2 g01184394 - Use Tooling (C) to install retaining ring (21) on shaft (23).
- Use a suitable press to install bearing (20) on shaft (23).
- Install spacer (22).
- Use a suitable press to install bearing (24) on shaft (23).
Show/hide table
Illustration 3 g01184384 - Apply clean engine oil to bearing (20) and bearing (24). Install the shaft assembly in body (16) and seal (15).
- Install ring (19) and shield (17). Use Tooling (A) to install retaining ring (18).
- Position gear (14) on the shaft assembly. Install bolt (11), washer (12), and washer (13).
Show/hide table
NOTICE Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
Show/hide tableIllustration 4 g01184484 - Use Tooling (F) to install the ceramic part of seal assembly (3) in housing (1).
Show/hide table
Illustration 5 g01184495 - Observe the location of alignment pin (25) in the housing (1).
- Install seal assembly (3).
- Use Tooling (A) to install retaining ring (4).
- Align Location (X) on plate (5) with the alignment pin in housing (1). Install plate (5) and impeller (6) in housing (1).
Show/hide table
Illustration 6 g01184339 - Install O-ring seal (7), bolts (10), washers (9), and cover (8) in housing (1).
Show/hide table
Illustration 1 | g01184403 |
End By:
- Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Caterpillar Information System:
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
3126B Generator Set Engine Sensors and Electrical Connectors
C32 Marine Engines Auxiliary Water Pump - Disassemble
C15 On-Highway Engine Electronic Unit Injector - Test
2008/07/21 New Inlet Valve Guide Seal and New Cylinder Head Groups {1104, 1225}
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
C15 Generator Sets Safety Messages
Work Area Vision System Camera Description
Work Area Vision System Display Description
Work Area Vision System Display Picture Adjustment - Select Display Settings
Work Area Vision System Display Position Adjustment
C4.4 and C6.6 Engines for Caterpillar Built Machines Injector Solenoid Circuit - Test
C13 and C15 On-highway Engines Diagnostic Trouble Codes
C32 Marine and Auxiliary Marine Engines Auxiliary Water Pump - Install
C32 Petroleum Engines Aftercooler - Remove
C15 On-Highway Engine Engine Valve Lash - Inspect/Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 1639 FMI 09
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Condenser - Remove and Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0041 FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0041 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0100 FMI 03
Reuse and Salvage for Fuel Injection Pumps and Nozzles on 3044, 3046, 3064, and 3066 Engines {1251} Reuse and Salvage for Fuel Injection Pumps and Nozzles on 3044, 3046, 3064, and 3066 Engines {1251}
2005/08/22 Troubleshooting Column-Type Fuel Level Senders {5574, 7481}
3126B Petroleum Engine Electronic Control Module - Remove and Install