Auxiliary Water Pump - Disassemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-1859 | Pliers | 1 |
B | 5F-7465 | Puller | 1 |
1P-7461 | Legs | 2 | |
5P-4750 | Screw | 1 | |
1P-0510 | Driver Gp | 1 | |
C | 1P-1861 | Pliers | 1 |
D | 9S-9152 | Bearing Puller | 1 |
E | 1P-0510 | Driver Gp | 1 |
F | 8S–6470 | Driver Gp | 1 |
Start By:
- Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (10), washers (9), and cover (8) from housing (1).
- Remove O-ring seal (7), from housing (1).
- Use Tooling (F) to remove impellar (6).
- Remove plate (5) from housing (1).
- Use Tooling (A) to remove retaining ring (4). Remove seal assembly (3) from housing (1).
- Remove bolts (2) and the washers. Remove housing (1).
Show/hide table
Illustration 2 g01184356 - Remove the ceramic part of seal assembly (3) when the shaft assembly is removed from the housing. Use Tooling (E) and a suitable press to remove the seal from housing (1).
Show/hide table
Illustration 3 g01184384 - Remove bolt (11), washer (12), and washer (13).
- Use Tooling (B) to remove gear (14) from the shaft assembly.
- Use Tooling (C) to remove retaining ring (18). Remove ring (19) and shield (17) from shaft assembly. Remove the shaft assembly from body (16) and seal (15).
Show/hide table
Illustration 4 g01184388 Show/hide tableIllustration 5 g01184394 - Use Tooling (D) and a suitable press to remove bearing (20) from shaft (23).
- Use Tooling (A) to remove retaining ring (21).
- Remove spacer (22).
- Use Tooling (D) and a suitable press to remove bearing (24) from shaft (23).
Show/hide table
Illustration 6 g01184403 - Use Tooling (E) and a suitable press to remove seal (15) from body (16).
Show/hide table
Illustration 1 | g01184339 |
Caterpillar Information System:
C15 On-Highway Engine Electronic Unit Injector - Test
2008/07/21 New Inlet Valve Guide Seal and New Cylinder Head Groups {1104, 1225}
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
C15 Generator Sets Safety Messages
Work Area Vision System Camera Description
Work Area Vision System Display Description
Work Area Vision System Display Picture Adjustment - Select Display Settings
Work Area Vision System Display Position Adjustment
C4.4 and C6.6 Engines for Caterpillar Built Machines Injector Solenoid Circuit - Test
C15 On-Highway Engine Basic Engine
Work Area Vision System General Information
Work Area Vision System Camera - Clean
3126B Generator Set Engine Sensors and Electrical Connectors
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
C32 Marine Engines Auxiliary Water Pump - Assemble
C13 and C15 On-highway Engines Diagnostic Trouble Codes
C32 Marine and Auxiliary Marine Engines Auxiliary Water Pump - Install
C32 Petroleum Engines Aftercooler - Remove
C15 On-Highway Engine Engine Valve Lash - Inspect/Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 1639 FMI 09
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Condenser - Remove and Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0041 FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0041 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0100 FMI 03