Steering Clutch and Brake - Assemble
Assembly Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 3 |
| B | 1P-0510 | Driver Gp | 1 |
- Clean all parts. Inspect all parts for wear or damage. Replace all parts that are damaged or worn.
- Install springs (26) into housing (13) .
Show/hide table
 | |
| Illustration 1 | g00952539 |
- Install O-ring seals (27) and (28) .
- Position piston (25) into housing (13) .
Show/hide table
 | |
| Illustration 2 | g00952538 |
- Install seals (23) and (24) on manifold assembly (22). Install the seals on the manifold assembly, as shown. Put clean oil on the lip of the seals.
Show/hide table
 | |
| Illustration 3 | g00952535 |
- Align the oil holes in manifold assembly (22) with the holes in housing (13). Install the manifold assembly and bolts (19) .
Show/hide table
 | |
| Illustration 4 | g00952533 |
- Raise the temperature of bearing (16) and install bearing (16) onto hub assembly (7). Bearing (16) must be seated squarely on the hub assembly after bearing (16) has cooled.
Show/hide table
 | |
| Illustration 5 | g00952514 |
- Install three rings (15) onto hub assembly (7) .
- Install bearing (14) into housing (13) .
Show/hide table
 | |
| Illustration 6 | g00952511 |
- Fasten a hoist and Tooling (A) onto housing (13) and lower the housing into position on hub assembly (7) .
Show/hide table
 | |
| Illustration 7 | g00952588 |
- Install ring (12) onto hub assembly (7) .
Show/hide table
 | |
| Illustration 8 | g00952507 |
- Start with a plate and install brake plates (20) and friction discs (21). Alternate the plates and discs.
Show/hide table
 | |
| Illustration 9 | g00952592 |
- Install plate (18) and bolts (17) onto housing (13) .
Show/hide table
 | |
| Illustration 10 | g00952627 |
- Install sleeve bearing (9) into hub assembly (7) .
Show/hide table
 | |
| Illustration 11 | g00952629 |
- Install seals (10) and (11) into piston (8) .
Show/hide table
 | |
| Illustration 12 | g00952262 |
Show/hide table
 | |
| Illustration 13 | g00952631 |
- Put clean oil on the seals and install piston (8) into hub assembly (7) .
- Install input hub (4) .
Show/hide table
 | |
| Illustration 14 | g00952634 |
- Start with a plate and install clutch plates (5) and friction discs (6) .
Show/hide table
 | |
| Illustration 15 | g00952637 |
- Install sleeve bearing (3) into plate (2) .
Show/hide table
 | |
| Illustration 16 | g00952257 |
Show/hide table
 | |
| Illustration 17 | g00952255 |
- Position plate (2) onto the housing and install bolts (1) .
End By: Connect the final drive, the steering clutch, and the brake. Refer to Disassembly and Assembly, "Final Drive, Steering Clutch, and Brake - Connect".
Caterpillar Information System:
D5N Track-Type Tractor Power Train Steering Clutch and Brake - Disassemble
963C Track-Type Loader Seat
963C Track-Type Loader Daily Inspection
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}
D6N Track-Type Tractor Engine Supplement Fan Drive - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Introduction - 938G Series II Wheel Loader
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
2003/02/03 Machine Components are Available for the Field Installation of the Product Link System {1408, 7602}
2003/02/03 New Flash Software is Available {7620}
3054E Industrial Engine Piston Cooling Jets - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Machine Systems Tilt Cylinder - Remove and Install
3406E Engine for Caterpillar Built Machines Sensors and Electrical Connectors
963C Track-Type Loader Operator Controls
854G Wheel Dozer Transmission Oil Sample - Obtain
3054E Industrial Engine Engine Oil Filter Base - Remove and Install
963C Track-Type Loader Monitoring System
D6N Track-Type Tractor Engine Supplement Engine - Remove
D6N Track-Type Tractor Engine Supplement Engine - Install
2003/01/27 The Lockup Clutch May be Enabled or Disabled with Cat ET {0785, 3102}
AD45 and AE40 II Underground Articulated Trucks Steering Cylinder Bearings - Lubricate
AD45 and AE40 II Underground Articulated Trucks Steering Stop - Check
3054E Industrial Engine Engine Oil Cooler - Remove
AD45 and AE40 II Underground Articulated Trucks Steering Tank Screen - Clean
3054E Industrial Engine Engine Oil Cooler - Install