Air Dryer - Remove and Install
Removal Procedure
Show/hide table
Pressurized air can cause personal injury. The air supply lines are pressurized to 830 kPa (120 psi). Purge the air from the system before performing any maintenance to the air system. |
- Park the machine on a hard, level surface. Lower the scraper bowl to the ground and engage the parking brake. Chock the wheels in order to prevent the machine from moving.
Note: Put identification marks on all hoses, on all wires, and on all tubes for installation purposes. Plug hoses and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
- Purge the air from the air tanks. The air tank valves are located on the left side of the cab.
- Open panel (1) in order to gain access to the air dryer.
Show/hide table
Illustration 1 | g01019739 |
- Remove hose assemblies (3) from air dryer (2) .
Show/hide table
Illustration 2 | g01019740 |
- Disconnect harness assembly (4) .
- Loosen hose clamp (5) and remove hose (6) from the air dryer.
- Remove bolts (8) from air dryer (2) .
Show/hide table
Illustration 3 | g01072216 |
- Remove bolt (7) from air dryer (2). Remove air dryer (2) from the machine.
Installation Procedure
- Position air dryer (2) onto the machine. Install bolts (8) and bolt (7) .
Note: Clean all parts and inspect all parts. If any parts are worn or damaged use new parts for replacement.
Show/hide table
Illustration 4 | g01072216 |
- Install hose (6) and tighten clamp (5) .
Show/hide table
Illustration 5 | g01019740 |
- Connect harness assembly (4) .
- Connect hose assemblies (3) onto air dryer (2) .
- Close panel (1) .
Show/hide table
Illustration 6 | g01019739 |
Caterpillar Information System:
623G Wheel Tractor-Scraper Machine Systems Roller (Floor) - Install
D6R Series II Track-Type Tractor Power Train Transmission Hydraulic Control
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Piston Pump Neutral - Adjust
D3G, D4G and D5G HYSTAT Track-Type Tractors Winch Systems Winch Control Centering - Adjust
D3G, D4G and D5G HYSTAT Track-Type Tractors Winch Systems Piston Pump Neutral - Adjust
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Crossover Relief Valve - Adjust
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Charge Relief Valve - Adjust
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Pressure Override Valve - Adjust
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Service Brake Switch - Adjust
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Steering - Test
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Final Hydrostatic Speed - Test
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Hydrostatic and Implement Stall - Test
D8R Series II Track-Type Tractor Hydraulic System Quick-Drop Valve
D8R Series II Track-Type Tractor Hydraulic System Bulldozer Lift Control Valve
621G and 627G Wheel Tractor-Scrapers Machine Systems Air Control Valve (Service Brake) - Remove and Install
621G and 627G Wheel Tractor-Scrapers Machine Systems Metering Pump (Steering) - Remove and Install
980G Series II Wheel Loader Engine Supplement Water Temperature Regulator - Remove and Install - Engine in Chassis
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0646 - FMI 05
3176C and 3406E Engines for Caterpillar Built Machines CID 0096 FMI 03 Fuel Level Sensor open/short to +batt
3176C and 3406E Engines for Caterpillar Built Machines CID 0096 FMI 04 Fuel Level Sensor short to ground
3456 Engines for Caterpillar Built Machines CID 0457 FMI 08 Brake Oil Temperature Sensor signal abnormal
3456 Engines for Caterpillar Built Machines CID 0826 FMI 08 Torque Converter Oil Temperature signal abnormal
D5N Track-Type Tractor Power Train General Information
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0646 - FMI 06