1. Home
  2. Caterpillar
  3. Testing and Adjusting
  4. #i01529778

D3G, D4G and D5G HYSTAT Track-Type Tractors Winch Systems Caterpillar


Winch Control Centering - Adjust

Usage:

D3G BYR
Show/hide table

Illustration 1g00818178

  • Lift rubber boot (2) from the base of winch control lever (1) .
      Show/hide table

      Illustration 2g00818181

    1. Loosen four hex nuts (3) .

    1. Adjust each of the four pins (4) until plate (5) is level from the front to the back and the plate is level from one side to the other side. The ball portion of each pin should barely touch the cartridge below the pin without depressing the cartridge.

    1. While you hold the pin in place, tighten the nut of one of the pins that has a washer. Tighten the nut to a torque of 13 ± 3 N·m (115 ± 27 lb in).

    1. Back off the opposite pin for approximately one quarter of a turn. While you hold the pin in place, tighten the nut to a torque of 13 ± 3 N·m (115 ± 27 lb in).

    1. Repeat Step 4 and Step 5 for the other two pins.

    1. Place the rubber boot around the base of the winch control lever.

    • Caterpillar Information System:

    D3G, D4G and D5G HYSTAT Track-Type Tractors Winch Systems Piston Pump Neutral - Adjust
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Crossover Relief Valve - Adjust
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Charge Relief Valve - Adjust
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Pressure Override Valve - Adjust
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Service Brake Switch - Adjust
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Steering - Test
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Final Hydrostatic Speed - Test
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Hydrostatic and Implement Stall - Test
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Hydrostatic Stall - Test
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Implement Stall - Test
    3456 Engines for Caterpillar Built Machines Throttle Switch Circuit - Test
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Deceleration Pedal - Test
    D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems Piston Pump Neutral - Adjust
    D6R Series II Track-Type Tractor Power Train Transmission Hydraulic Control
    623G Wheel Tractor-Scraper Machine Systems Roller (Floor) - Install
    621G and 627G Wheel Tractor-Scrapers Machine Systems Air Dryer - Remove and Install
    D8R Series II Track-Type Tractor Hydraulic System Quick-Drop Valve
    D8R Series II Track-Type Tractor Hydraulic System Bulldozer Lift Control Valve
    621G and 627G Wheel Tractor-Scrapers Machine Systems Air Control Valve (Service Brake) - Remove and Install
    621G and 627G Wheel Tractor-Scrapers Machine Systems Metering Pump (Steering) - Remove and Install
    980G Series II Wheel Loader Engine Supplement Water Temperature Regulator - Remove and Install - Engine in Chassis
    IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0646 - FMI 05
    3176C and 3406E Engines for Caterpillar Built Machines CID 0096 FMI 03 Fuel Level Sensor open/short to +batt
    3176C and 3406E Engines for Caterpillar Built Machines CID 0096 FMI 04 Fuel Level Sensor short to ground
    Back to top
    Contacts My AVS
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.