Gear Pump (Transmission Charging and Scavenge)
Show/hide table
| |
| Illustration 1 | g02628196 |
Show/hide table
| Specification for 262-6672 Gear Pump and Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 6V-5842 Bolt | Torque to |
| 2 | 1 | 8T-0644 Bolt | Torque to |
Show/hide table
| |
| Illustration 2 | g02671456 |
Show/hide table
| Specification for 262-6672 Gear Pump and Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| Lubricate the gear pump group with clean oil before you operate. The gear pump group must rotate freely by using your hand. | |||
| C | - | - | Diameter of the new shaft is |
| D | 4 | 8M-8489 Dowel | Extension of the dowel from the face of the oil pump body assembly (3) is |
| 4 | 8 | 6Y-5010 Washer | Assemble rubber coated washers on each side of ground steel washer. |
Show/hide table
| |
| Illustration 3 | g02671956 |
|
Detail E | |
Show/hide table
| Specification for 262-6672 Gear Pump and Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| K | - | - | Location of the joints of four bushings from the vertical centerline 30 ± 15 degrees. |
| 5 | 2 | 5M-1995 Bushing | Bore of the bushing after installation is Installation depth is |
Show/hide table
| |
| Illustration 4 | g02676057 |
|
Detail G | |
Show/hide table
| Specification for 262-6672 Gear Pump and Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| M | - | - | Location of the joints of four bushings from the vertical centerline 30 ± 15 degrees. |
| 6 | 2 | 5M-1995 Bushing | Bore of the bushing after installation is Installation depth of the bushing is |
Show/hide table
| |
| Illustration 5 | g02676077 |
|
Detail H | |
Show/hide table
| Specification for 262-6672 Gear Pump and Mounting Gp | |||
| Item | Qty | Part | Specification Description |
| P | 1 | 9N-4155 Adapter | Extension of the adapter from the face of the manifold (7) is |
| R | 2 | 8M-8489 Dowel | Extension of the dowel from the face of the manifold (7) is |
Caterpillar Information System:
C13 Engines for Caterpillar Built Machines Event Codes
3054E Industrial Engine Fuel Injection Nozzle Cover - Remove and Install
C27 and C32 Generator Set Engines Housing (Rear) - Remove
C4.4 Marine Generator Set Generator Operation
XQ60 Rental Generator Set Generator Set Installation
C27 and C32 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - C32
C27 and C32 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
120M, 12M, 140M and 160M Motor Graders Transmission Pressures - Test and Adjust
XQ60 Rental Generator Set Insulation - Test
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator - Dry
120M, 12M, 140M and 160M Motor Graders Power Train Charge System Pressure - Test and Adjust
XQ60 Rental Generator Set Rotating Rectifier - Test
D Series Excavator Monitoring System Maintenance Information Mode
C15 Generator Set Engines E363 High Fuel Supply Temperature
C27 and C32 Industrial and Petroleum Engines E443 High Auxiliary Pressure
C27 and C32 Industrial and Petroleum Engines E445 High Auxiliary Temperature
C3.3 and C4.4 Generator Sets Generator Set Identification
3512C HD SR500 Generator Sets Generator Set Vibration - Inspect
C27 and C32 Generator Set Engines Housing (Rear) - Install
C4.4 Generator Sets Alternator - Inspect
G3520C and G3520E Engines Air Lines - Compressor Bypass
C27 and C32 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove
C27 and C32 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install
2005/02/28 New Flash Files Are Available For Cold Mode Starting Strategy {7620}