Transmission Oil Cooler - Install - Engine In Chassis
Installation Procedure
- Clean the mating surfaces of the transmission oil cooler and the bonnets. Install a new gasket at both ends of the transmission oil cooler.
- Attach a suitable hoist and lifting slings to transmission oil cooler (10), as shown.
Show/hide table
Illustration 1 | g00640543 |
- Use the hoist in order to install transmission oil cooler (10). The weight of transmission oil cooler (10) is 43 kg (95 lb).
- Install four bolts (17) .
Note: It may be necessary to leave bolts (17) loose at this time in order to connect remaining parts. Tighten bolts (17) to the proper torque upon completion of installation.
Show/hide table
Illustration 2 | g00640544 |
- Install bolts (16) .
Show/hide table
Illustration 3 | g00640548 |
- Install new gasket (15) on the top of transmission oil cooler (10), as shown.
Show/hide table
Illustration 4 | g00640550 |
- Install top elbow (14) with three bolts (11), as shown.
Show/hide table
Illustration 5 | g00640555 |
Note: It is necessary to put three bolts (11) in the top elbow prior to installation.
- Install new gasket (13) and four bolts (12) .
Show/hide table
Illustration 6 | g00640557 |
- Install three remaining bolts (11) .
- Connect hose assembly (9) to transmission oil cooler (10) .
Show/hide table
Illustration 7 | g00640560 |
- Install tube assembly (8) and four bolts (7) .
Show/hide table
Illustration 8 | g00640562 |
- Connect hose assemblies (6) .
Show/hide table
Illustration 9 | g00640563 |
- Install clamp (5) .
- Install cover (4) and four bolts (3) .
Show/hide table
Illustration 10 | g00640565 |
- Install the left side engine panel (1) .
Show/hide table
Illustration 11 | g00855169 |
- Close access door (2) .
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect" for the machine that is being serviced.
Caterpillar Information System:
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System MID 082 - CID 0590 - FMI 09
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System MID 082 - CID 0498 - FMI 06
908 Compact Wheel Loader Hydraulic System Solenoid Valve and Mounting (Coupler and Parking Brake)
3056 Engine for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMSpc Software
992G Wheel Loader Electrohydraulic System Main Hydraulic System
515 Wheel Skidder and 525 Wheel Skidder Braking System Service Brake Control - Adjust
980G Wheel Loader Hydraulic System Hydraulic Fan Speed - Test and Adjust
908 Compact Wheel Loader Power Train System Piston Pump (Hydrostatic)
3114, 3116, and 3126 Engines for Caterpillar Built Machines Water Pump - Disassemble
3126B Engines for Caterpillar Built Machines Camshaft - Remove
3126B Engines for Caterpillar Built Machines Camshaft - Install
988G Wheel Loader Engine Supplement Transmission Oil Cooler - Remove - Engine In Chassis
992G Wheel Loader and 854G Wheel Dozer Steering System Relief Valve (Secondary Steering) - Test and Adjust - If Equipped
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMSpc Onboard Configuration
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMSpc Payload Reports
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Balancer Shaft - Remove and Install
D10R and D11R Track-Type Tractors Vital Information Display System (VIDS) General Information
C-9 Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
973C Track-Type Loader Power Train Rollover Protective Structure (ROPS)
973C Track-Type Loader Power Train ROPS Mounting
973C Track-Type Loader Power Train Hydrostatic Drive Motor
902 and 906 Compact Wheel Loaders Machine Systems Hydraulic Oil Cooler - Remove and Install
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System MID 082 - CID 0596 - FMI 12