Engine Oil Pressure Sensor - Remove and Install
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the engine oil into a suitable container.
- Remove wire connector (1) from oil pressure sensor (2) .
Show/hide table
 | |
| Illustration 1 | g00640365 |
- Remove oil pressure sensor (2) from the cylinder block. Plug the opening immediately.
Installation Procedure
- Install oil pressure sensor (2) into the cylinder block. Tighten the oil pressure sensor to 7 to 12 N·m (62 to 106 lb in).
Show/hide table
| | |
| Illustration 2 | g00640365 |
- Connect wire connector (1) to the engine oil pressure sensor (2) .
- Fill the engine with oil. Refer to the Operation and Maintenance Manual, "Refill Capacities" for the engine oil capacity.
Caterpillar Information System:
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMSpc Software
992G Wheel Loader Electrohydraulic System Main Hydraulic System
515 Wheel Skidder and 525 Wheel Skidder Braking System Service Brake Control - Adjust
980G Wheel Loader Hydraulic System Hydraulic Fan Speed - Test and Adjust
908 Compact Wheel Loader Power Train System Piston Pump (Hydrostatic)
3114, 3116, and 3126 Engines for Caterpillar Built Machines Water Pump - Disassemble
3126B Engines for Caterpillar Built Machines Camshaft - Remove
3126B Engines for Caterpillar Built Machines Camshaft - Install
3176C and 3196 Engines for Caterpillar Built Machines Piston Cooling Jet
992G Wheel Loader Electrohydraulic System Pilot Hydraulic System
908 Compact Wheel Loader Machine Systems Coupler Cylinder - Remove and Install
992G Wheel Loader and 854G Wheel Dozer Steering System Piston Pump (Steering) Margin Pressure - Test and Adjust
908 Compact Wheel Loader Hydraulic System Solenoid Valve and Mounting (Coupler and Parking Brake)
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System MID 082 - CID 0498 - FMI 06
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System MID 082 - CID 0590 - FMI 09
988G Wheel Loader Engine Supplement Transmission Oil Cooler - Install - Engine In Chassis
988G Wheel Loader Engine Supplement Transmission Oil Cooler - Remove - Engine In Chassis
992G Wheel Loader and 854G Wheel Dozer Steering System Relief Valve (Secondary Steering) - Test and Adjust - If Equipped
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMSpc Onboard Configuration
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMSpc Payload Reports
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Balancer Shaft - Remove and Install
D10R and D11R Track-Type Tractors Vital Information Display System (VIDS) General Information
C-9 Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
973C Track-Type Loader Power Train Rollover Protective Structure (ROPS)