Camshaft Bearings - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 129-6671 | Reaction Sleeve | 1 |
| 129-6672 | Puller Plate | 1 | |
| 129-6673 | Bearing Pilot | 1 | |
| 129-6674 | Backup Plate | 1 | |
| 6F-7032 | Bolt | 1 | |
| 1P-5542 (1) | Taperlock Stud | 1 | |
| C | 8S-2241 (2) | Camshaft Bearing Tool Group | 1 |
Show/hide table
| ( 1 ) | Part of 1P-5545 Adapter Gp |
| ( 2 ) | All of the tools that are listed above are used with Tooling (C) . |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position new camshaft bearings (1) in Tooling (A) and install the bearings from the rear to the front of the engine.
Show/hide table
 | |
| Illustration 1 | g01016694 |
Show/hide table
| NOTICE |
|---|
Location of the camshaft bearing lubrication holes is critical. Position the clinch butt joint up for all seven camshaft bearings. The No. 1 camshaft bearing oil hole is located 115 degrees counter clockwise from top center to align with the oil supply passage in the block. Camshaft bearings No. 2 through No. 7 are installed with the oil hole 45 degrees clockwise from top center. All are viewed from the front of the engine. Camshaft bearings 1,2,3,4,5, and 6 are the same width. Camshaft bearing No. 7 has a smaller width. Refer to the Specifications Manual for more information. |
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
- Install the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Install
615C Series II Wheel Tractor-Scraper Air System and Brakes Air Tank
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System Related Components
3056 Engine for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System Switches
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System VIMS-PC Software
515 and 525 Wheel SkiddersMachine Systems Heater Coil - Remove and Install
D6R Series II Track-Type Tractor Power Train Torque Converter
3056 Engine for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
C9 Engine For Caterpillar Built Machines Crankshaft Main Bearings - Install
3524B Engines for Off-Highway Trucks System Configuration Parameters
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks System Overview
3176C and 3196 Industrial Engines Camshaft Bearings - Remove
980G Wheel Loader Power Train Torque Converter
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Ground Level Shutdown Switch
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System Data Link
515 and 525 Wheel SkiddersMachine Systems Brake Accumulator - Remove and Install
973 Track-Type Loader General Operation
973 Track-Type Loader Bulldozing
992G Wheel Loader and 854G Wheel Dozer Steering System General Information (Steering)
3056 Engine for Caterpillar Built Machines Water Outlet Manifold - Remove
797 and 797B Off-Highway Truck/Tractors Braking System Service Tools
973 Track-Type Loader Dumping
973 Track-Type Loader Digging