Engine Oil Bypass Valve
Show/hide table
 | |
| 图 1 | g00888110 |
旁路压力 ... 345 至 414 kPa (50 至 60 psi)
(1) 挡圈
(2) 端板
(3) 弹簧
- 组装后的长度 ... 55.6 mm (2.19 in)
- 组装长度上的负载 ... 12.9 至 18.6 N·m (9.52 至 13.72 lb ft)
(4) 柱塞
- 柱塞直径 ... 18.16 至 18.18 mm (0.715 至 0.716 in)
(5) 阀体
- 柱塞孔直径 ... 18.24 至 18.27 mm (0.718 至 0.719 in)
- 柱塞在孔中的间隙 ... 0.06 至 0.11 mm (0.002 至 0.004 in)
Caterpillar Information System:
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Retarder Operation - Test
3056 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3056 Engine for Caterpillar Built Machines Rocker Shaft - Assemble
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Engine Fan Control Solenoid
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0829 - FMI 04 Rear Aftercool Temperature short to ground
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3013, 3014 and 3024 Engines
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0829 - FMI 03 Rear Aftercool Temperature open/short to +batt
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0800 - FMI 09 Unable to communicate with VIMS
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0569 - FMI 06 Oil Renewal Solenoid short to ground
3056 Engine for Caterpillar Built Machines Rocker Shaft - Disassemble
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Transmission Oil Pump Pressure - Test and Adjust
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0569 - FMI 05 Oil Renewal Solenoid open circuit
902 and 906 Compact Wheel Loaders Machine Systems Pilot Accumulator - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Assemble - 3013, 3014, and 3024 Engines
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Blast Number Entering
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C-9 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Machine Status Delay
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Check Valve (Ride Control)
3056 Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove
824G , 825G and 826G Landfill Compactor Brake Discs - Check
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System Implement Electronic Control (Ripper)
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Transmission Lubrication Relief Valve Pressure - Test
924G and 924Gz Wheel Loaders Power Train Differential Pinion Preload - Adjust