Engine Oil Pan - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Loosen oil drain valve (1) or remove the oil drain plug and the O-ring seal. Drain the engine oil into a suitable container for storage or disposal.
- Remove bolts (2) from engine oil pan (3).
- Remove engine oil pan (3) and the gasket from the cylinder block.
Show/hide table
| |
| Illustration 1 | g00902366 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean all surfaces thoroughly. Inspect the condition of the gasket. Replace the gasket, if necessary.
Show/hide table
Illustration 2 g00902366 - Install the gasket and engine oil pan (3) in the correct position on the cylinder block.
- Install bolts (2) in order to fasten engine oil pan (3) to the cylinder block. Tighten bolts (2) to a torque of
22 N·m (16 lb ft) . - Tighten oil drain valve (1) or install the O-ring seal and the drain plug. Tighten the drain plug to a torque of
34 N·m (25 lb ft) . - Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.
Note: Refer to the Operation and Maintenance Manual, SEBU7645, "Refill Capacities" for more information.
Caterpillar Information System:
3056 Engine for Caterpillar Built Machines Rocker Shaft - Assemble
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Engine Fan Control Solenoid
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0829 - FMI 04 Rear Aftercool Temperature short to ground
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3013, 3014 and 3024 Engines
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0829 - FMI 03 Rear Aftercool Temperature open/short to +batt
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0800 - FMI 09 Unable to communicate with VIMS
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0569 - FMI 06 Oil Renewal Solenoid short to ground
3056 Engine for Caterpillar Built Machines Rocker Shaft - Disassemble
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Transmission Oil Pump Pressure - Test and Adjust
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0569 - FMI 05 Oil Renewal Solenoid open circuit
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0562 - FMI 09 Unable to Communicate with Cat Monitoring System
924G and 924GZ Wheel Loaders Steering System Steering System Troubleshooting
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Retarder Operation - Test
3056E Industrial Engine Engine Oil Bypass Valve
902 and 906 Compact Wheel Loaders Machine Systems Pilot Accumulator - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Assemble - 3013, 3014, and 3024 Engines
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Blast Number Entering
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C-9 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Machine Status Delay
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Check Valve (Ride Control)
3056 Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove
824G , 825G and 826G Landfill Compactor Brake Discs - Check
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System Implement Electronic Control (Ripper)