Alternator and Regulator
Show/hide table
| |
| 图 1 | g03393001 |
注: 用碳堆式 4C-4911 蓄电池负载测试仪加载蓄电池以达到最大交流发电机输出。
Show/hide table
| 177-9953 充电交流发电机总成的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | - | - | 在拧紧螺栓 (3) 之前，将螺栓拧紧至扭矩为 |
| 2 | 1 | 2K-4821 锁紧螺母 | 拧紧至扭矩为 |
| 3 | 1 | 5S-7349 螺栓 | (B-) 接线端。 拧紧至扭矩为 |
| 4 | 1 | 185-2648 电压调节器组件 | 不需要调整电压设置。
允许电压范围为 27 到 29 V。 |
| 5 | - | - | (R) 接线端为来自定子的交流输出，不可用于诊断。 |
| 6 | 1 | 6V-8189 螺母 | 对于 (B+) 接线端，使用 7/16 环形端子。 |
| (B+) 接线端。 拧紧至扭矩为 |
|||
| - | - | - | 电压为 24 V。 |
| - | - | - | 电流为 80 安培。 |
| - | - | - | 极性为负极接地。 |
| - | - | - | 旋转方向为顺时针方向。 |
| - | - | - | 5000 rpm 时的最小满载电流为 85 安培。 |
| - | - | - | 1500 rpm 时的最小满载电流为 16 安培。 |
| - | - | - | 输出电压为 28 ± 1 V。 |
Caterpillar Information System:
2004/12/01 New Cooling Screens in TMI for Electric Power Packages {1353}
3508C, 3512C and 3516C Marine Engines Engine Oil Pressure Sensor - Remove and Install
2004/12/01 Updated Information to Operation and Maintenance Manual, SEBU6251 , "Engine Oil (3116 and 3126 Marine Engines" {1348, 7581}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Pressure Switch (Refrigerant Pressure Cutoff)
345C Excavator Hydraulic System Pump Control (Output Flow) - Adjust
3500B High Displacement Generator Set Engines Reference Material
C9 Industrial Engines Plate Locations and Film Locations
C7 Petroleum Engine Engine Oil and Filter - Change
3508C, 3512C and 3516C Marine Engines Turbocharger Inlet Pressure Sensor - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Expansion Valve
3508C, 3512C and 3516C Marine Engines Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Fuel Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Crankcase Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Aftercooler Coolant Temperature Sensor - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Heater Core (Cab)
3508C, 3512C and 3516C Marine Engines Fuel Priming Pump - Remove and Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Air Cleaner Element (Single Element) - Replace
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines After Stopping Engine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
345C MHPU Mobile Hydraulic Power Unit Radiator Core - Clean
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Remove