Crankcase Pressure Sensor - Remove and Install
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 断开线束组件并拆下曲轴箱压力传感器 (1)。
- 将 O 形密封圈从曲轴箱压力传感器上拆下。
Show/hide table
| |
| 图 1 | g01129987 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 安装一个新的 O 形密封圈到曲轴箱压力传感器 (1) 上。
- 安装曲轴箱压力传感器 (1) 并拧紧至扭矩为
10 ± 2 N·m (89 ± 18 lb in) 。 - 连接线束组件。
Show/hide table
|
| |
| 图 2 | g01129987 |
Caterpillar Information System:
3508C, 3512C and 3516C Marine Engines Fuel Pressure Sensor - Remove and Install
3406C Engines for Caterpillar Built Machines Alternator and Regulator
2004/12/01 New Cooling Screens in TMI for Electric Power Packages {1353}
3508C, 3512C and 3516C Marine Engines Engine Oil Pressure Sensor - Remove and Install
2004/12/01 Updated Information to Operation and Maintenance Manual, SEBU6251 , "Engine Oil (3116 and 3126 Marine Engines" {1348, 7581}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Pressure Switch (Refrigerant Pressure Cutoff)
345C Excavator Hydraulic System Pump Control (Output Flow) - Adjust
3500B High Displacement Generator Set Engines Reference Material
C9 Industrial Engines Plate Locations and Film Locations
C7 Petroleum Engine Engine Oil and Filter - Change
3508C, 3512C and 3516C Marine Engines Turbocharger Inlet Pressure Sensor - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Expansion Valve
3508C, 3512C and 3516C Marine Engines Aftercooler Coolant Temperature Sensor - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Heater Core (Cab)
3508C, 3512C and 3516C Marine Engines Fuel Priming Pump - Remove and Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Air Cleaner Element (Single Element) - Replace
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines After Stopping Engine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
345C MHPU Mobile Hydraulic Power Unit Radiator Core - Clean
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Remove
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Install
C9 Engines for Caterpillar Built Machines Aftercooler - Test