After Stopping Engine
注: 检查发动机油之前，停止运行发动机至少 10 分钟以使发动机油有充分的时间回到油底壳。
- 检查曲轴箱油位。 将油位保持在油位表的"添加 (ADD)"标记和"已满 (FULL)"标记之间。
- 如有必要，进行小的调整。 修理所有渗漏处，并拧紧所有松动的螺栓。
- 记下工时表的读数。 实施操作和保养手册, "保养周期表"中所述的保养。
- 加满燃油箱，以帮助防止燃油中积聚湿气。 燃油箱不要加油过满。
Show/hide table
| 注意 |
|---|
|
仅使用本操作和保养手册, "再加注容量和建议"推荐的防冻剂/冷却液混合液。 |
- 冷却发动机。 检查冷却液液位。 将冷却液液位保持在加注管底部以下
13 mm (0.5 inch) 以内。 - 如果预料到结冻温度，要检查冷却液的防冻剂保护是否正确。 必须保护冷却系统，防其在预计的最低外部温度下结冻。 如有必要，添加适当的冷却液/水混合液。
- 对所有从动设备进行必需的定期保养。 此保养在 OEM（原始设备制造商）的使用说明书中有所述及。
Caterpillar Information System:
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Air Cleaner Element (Single Element) - Replace
3508C, 3512C and 3516C Marine Engines Fuel Priming Pump - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Heater Core (Cab)
3508C, 3512C and 3516C Marine Engines Aftercooler Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Crankcase Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Fuel Pressure Sensor - Remove and Install
3406C Engines for Caterpillar Built Machines Alternator and Regulator
2004/12/01 New Cooling Screens in TMI for Electric Power Packages {1353}
3508C, 3512C and 3516C Marine Engines Engine Oil Pressure Sensor - Remove and Install
2004/12/01 Updated Information to Operation and Maintenance Manual, SEBU6251 , "Engine Oil (3116 and 3126 Marine Engines" {1348, 7581}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Pressure Switch (Refrigerant Pressure Cutoff)
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
345C MHPU Mobile Hydraulic Power Unit Radiator Core - Clean
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Remove
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Install
C9 Engines for Caterpillar Built Machines Aftercooler - Test
VR6B Voltage Regulator Installation For 480V Sensing VR3 Regulators On 3500 Generator Sets {4467} VR6B Voltage Regulator Installation For 480V Sensing VR3 Regulators On 3500 Generator Sets {4467}
G3612 and G3616 Engines Connecting Rod Bearings - Inspect/Replace
3508B, 3512B and 3516B Generator Set Engines Electric Starting Motor - Remove and Install
3500 Engines Prelubrication Oil Pump - Remove and Install
G3612 and G3616 Engines Specifications
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning and Heating System Sensor Operation