Track Roller Frame - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 236-1192 | Brace Assembly | 1 |
B | 8S-7611 | Tube | 4 |
8S-7640 | Stand | 4 | |
8S-7615 | Pin | 4 | |
C | 138-7573 | Link Bracket | 2 |
E | 1U-6396 | O-Ring Assembly Compound | 1 |
Show/hide table
Personal injury or death can result from a falling loader bucket or lift arms. Install the necessary Tooling and tilt the bucket all the way forward so it can not drop before working beneath a raised bucket. |
Note: The O-ring seal, gaskets, and seals should always be replaced. A used O-ring seal may not have the same sealing properties as a new O-ring seal. A reconditioning procedure should not be degraded because of a low cost component such as an O-ring seal or a gasket. Use Tooling (E) during the assembly procedure.
- Check the condition of the seal on the pivot shaft before the installation of the track roller frame. Refer to Disassembly and Assembly, "Pivot Shaft - Remove and Install".
Show/hide table
Illustration 1 g00577675 - Install Tooling (C) in the track roller frame. Support the track roller frame assembly with a suitable lifting device, as shown. Move the track roller frame into position. The weight of the track roller frame is approximately
1474 kg (3250 lb) .Show/hide tableIllustration 2 g00726477 - Install pin assembly (14) in order to secure track roller frame (12) to equalizer bar (13). Install bolt (15).
Show/hide table
Illustration 3 g00726342 - Install plate (11) and bolts (10) on the pivot shaft.
Show/hide table
Illustration 4 g00726531 - Install the O-ring seal on the cover. Install cover (2) with bolts (1).
Show/hide table
Illustration 5 g00723293 Show/hide tableIllustration 6 g00723205 - Install guard assembly (8), bolts (7), and bolts (9).
- Install guard assemblies (4) with the washers and bolts (5) to the track roller frame. Do not tighten bolts (5) at this time. Install bar (6) and bolts (3) in order to secure the guard assemblies.
- Raise the lift arms and install Tooling (A).
Show/hide table
Illustration 7 g00577664 - Lift the machine. Remove Tooling (B). Lower the machine onto the tracks.
- Remove Tooling (A) and lower the lift arms to the ground.
End By:
- Connect the tracks. Refer to Disassembly and Assembly, "Track - Connect".
Caterpillar Information System:
D6R Series II Track-Type Tractor Hydraulic System Oil Cooler and Bypass Valve
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
613C Series II Wheel Tractor-Scraper Transmission Neutral Lock Control
613C Series II Wheel Tractor-Scraper Transmission Control
3406E On-Highway Engine Pistons and Connecting Rods - Remove
D11T Track-Type Tractor Hydraulic System Hydraulic Pump
615C Series II Wheel Tractor-Scraper Parking and Secondary Brake Control
D6R Series II Track-Type Tractor Hydraulic System Main Relief Valve
611 Wheel Tractor-Scraper Wheel Tractor-Scraper Power Train Transmission Hydraulic Control Linkage - Adjust
994D Wheel Loader Engine Supplement Air Starting Motor - Remove and Install
3034 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
3034 Engine for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
615C Series II Wheel Tractor-Scraper Transmission Control
613C Series II Wheel Tractor-Scraper Bowl Control
613C Series II Wheel Tractor-Scraper Ejector Control
613C Series II Wheel Tractor-Scraper Elevator Control
615C Series II Wheel Tractor-Scraper Transmission Neutral Lock Control
3408E and 3412E Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Remove
3034 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
3408E and 3412E Engines for Caterpillar Built Machines Air in Fuel - Test
963C Track-Type Loader Power Train Equalizer Bar - Install
3406E On-Highway Engine Connecting Rod Bearings - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Base