Alternator - Remove and Install
Removal Procedure
Show/hide table
Disconnect batteries before performance of any service work. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Disconnect all electrical connections to the alternator before proceeding. Mark the connections or identify the connections for later installation.
- Loosen bolt (2) and bolt (4) .
Show/hide table
Illustration 1 | g00577662 |
- Slide alternator (3) toward the engine.
- Remove alternator V-belt (1) from the alternator pulley.
- Remove bolts (2) and (4) .
- Remove alternator (3) from the engine.
Installation Procedure
- Put alternator (3) in position on the engine.
Show/hide table
Illustration 2 | g00577662 |
- Install bolts (2) and (4). Tighten bolts (2) and (4) finger tight.
- Install alternator V-belt (1) .
Note: When you install the alternator, ensure that the alternator pulley is in alignment with the crankshaft pulley within 2.4 mm (0.09 inch).
- Slide alternator (3) away from the engine in order to tension alternator V-belt (1). For more information on the tension for the alternator V-belt, refer to the Testing and Adjusting Module, "Belt Tension Chart".
- Tighten bolt (2) to a torque of 12 N·m (9 lb ft).
- Tighten bolt (4) to a torque of 24 N·m (18 lb ft).
Note: Reconnect all electrical connections to the alternator before you operate the engine.
Caterpillar Information System:
611 Wheel Tractor-Scraper Wheel Tractor-Scraper Power Train Visual Inspection
3176C and 3196 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
D6R Track-Type Tractor Safety Signs and Labels
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Disassemble
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Injection Control Linkage
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Install
994D Wheel Loader Engine Supplement Air Cleaner - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove
613C Series II Wheel Tractor-Scraper Parking and Secondary Brake Control
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Governor
611 Wheel Tractor-Scraper Air System and Brakes Air Compressor Governor - Test and Adjust
3508B Engine for Caterpillar Built Machines Turbocharger Exhaust Temperature Sensor
988G Wheel Loader Bucket Wear Plates - Inspect/Replace
D7R Series II Track-Type Tractor Hydraulic System Implement Control Valve
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Assemble
3034 Engine for Caterpillar Built Machines Electric Starting Motor - Remove and Install
966G and 972G Wheel Loaders Equipment Lowering with Engine Stopped
3034 Engine for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
3034 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
994D Wheel Loader Engine Supplement Air Starting Motor - Remove and Install
611 Wheel Tractor-Scraper Wheel Tractor-Scraper Power Train Transmission Hydraulic Control Linkage - Adjust
D6R Series II Track-Type Tractor Hydraulic System Main Relief Valve
615C Series II Wheel Tractor-Scraper Parking and Secondary Brake Control
D11T Track-Type Tractor Hydraulic System Hydraulic Pump