Ripper Shank - Remove and Install
Removal Procedure
- Position the machine on an incline, as shown. Block the front of the machine and apply the service brake.
Show/hide table
Illustration 1 | g00536875 |
Show/hide table
Illustration 2 | g00536876 |
- Lower ripper shank (1) onto blocks, as shown. Retract shank pin (2) .
- Slowly raise the ripper frame until first bore (3) on ripper shank (1) will clear the carriage.
- Install pin (4) in bore (3), as shown. Position the forks on the lift truck on each side of the ripper shank, as shown. Secure the ripper shank to the carriage of the lift truck.
Show/hide table
Illustration 3 | g00536919 |
Show/hide table
To prevent possible personal injury during removal of the ripper shank, keep away from the area around the lift truck. The ripper shank may fall off the forks of the lift truck during the removal procedure. |
- Raise ripper shank (1) off the blocks with a lift truck and remove the blocks.
- Lower ripper shank (1) to the ground with the lift truck.
- Raise the ripper frame until ripper shank (1) will clear the carriage. Use a lift truck to remove ripper shank (1). The weight of the ripper shank is approximately 1352 kg (2975 lb).
Installation Procedure
- Position the machine on an incline. Block the front of the machine and apply the service brake.
Show/hide table
Illustration 4 | g00536919 |
- Install pin (4) in the bore, as shown. Position the forks on the lift truck on each side of the ripper shank, as shown. Secure the ripper shank to the carriage of the lift truck.
- Raise the ripper frame until ripper shank (1) will clear the carriage. Use a lift truck to install ripper shank (1). The weight of the ripper shank is approximately 1352 kg (2975 lb).
- Raise ripper shank (1) into position with the lift truck.
- Slowly lower the ripper frame until bore (3) is in alignment.
Show/hide table
Illustration 5 | g00536876 |
Show/hide table
Illustration 6 | g00536875 |
- Extend shank pin (2) .
Caterpillar Information System:
D11R Track-Type Tractor Machine Systems Ripper Shank - Remove and Install
D11R Carrydozer Track-Type Tractor Pitch Regenerate Solenoid Valve - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Disassemble
D11R Carrydozer Track-Type Tractor Pitch Regenerate Solenoid Valve - Disassemble
D11R Carrydozer Track-Type Tractor Pitch Regenerate Solenoid Valve - Install
D11R Carrydozer Track-Type Tractor Pitch Regenerate Solenoid Valve - Remove
988G Wheel Loader Window Wiper - Inspect/Replace
834G Wheel Tractor and 836G Landfill Compactor Steering System Steering Pilot System
836G Landfill Compactor and 834G Wheel Dozer Belts - Inspect/Adjust/Replace
SR4 HV and SR4B HV Generators Varistor - Test
3306C Engines for Caterpillar Built Machines Alternator and Regulator
545 Wheel Skidder Power Train Bottom Guard (Rear Axle) - Remove and Install
545 Wheel Skidder Power Train Differential Pinion - Remove
545 Wheel Skidder Power Train Solenoid Valve (Differential Lock)
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Assemble
988G Wheel Loader Braking System Parking Brake - Manual Release
988G Wheel Loader Steering System Pilot Valve (STIC Steering)
3406E and 3456 Engines for Caterpillar Built Machines Turbocharger - Install
988G Wheel Loader Loader Pins and Bearings - Lubricate
545 Wheel Skidder Power Train Axle Housing - Disassemble
322B, 322B L, 325B and 325B L Excavators Travel Control - Straight Travel Pedal (If Equipped)
988G Wheel Loader Braking System Parking Brake - Test
988G Wheel Loader Braking System Parking Brake Control Cable - Adjust
988G Wheel Loader Bucket Rated Load