Transmission and Bevel Gears - Install
Installation Procedure
Show/hide table
Required Tools     | A     | B     |
FT-1897 Adapter     | 1     |     |
138-7575 Link Bracket     | 1     | 2     |
- Put O-ring seals (13) and (14) into position on the main frame case.
Show/hide table
Illustration 1 | g00560565 |
- Install the O-ring seal on the transmission and the bevel gear case.
- Fasten a hoist and Tooling (B) to the transmission and bevel gear (10) .
Show/hide table
Illustration 2 | g00560562 |
Show/hide table
Illustration 3 | g00560553 |
- Put the transmission and the bevel gears into position in the main frame case. Rollers (11) must be against the stops on the rail assemblies, as shown.
- Put a two ton floor jack (12) into position under the rear of the transmission in order to support the transmission and the bevel gear when the hoist is removed.
- Remove the hoist and Tooling (B) .
- Fasten a hoist to Tooling (A). Support the weight of the transmission and the bevel gears with the hoist. Remove the floor jack.
Show/hide table
Illustration 4 | g00560568 |
- Install two 12 mm guide bolts (15) in the main frame case.
- Use the hoist and Tooling (A) in order to put the transmission and the bevel gears (10) into position on guide bolts (15) .
- Install the bolts that hold the transmission and the bevel gears to the main frame case.
- Remove the hoist and Tooling (A) .
- Install the gasket and cover (8) to the rear of the transmission.
Show/hide table
Illustration 5 | g00560548 |
- Install harness connector (4) and jam nut (5) on cover (7) .
Show/hide table
Illustration 6 | g00560544 |
- Install the gasket, cover (7), and bolts (6) .
- Connect wire harness (3) to the transmission and the bevel gear.
Show/hide table
Illustration 7 | g00560519 |
- Install cover assembly (2) and bolts (1) .
Show/hide table
Illustration 8 | g00560516 |
- Fill the transmission and the bevel gear case with oil to the correct level.
End By:
- Install the main drive shaft. Refer to Disassembly and Assembly, "Main Drive Shaft - Remove and Install" for the machine that is being serviced.
- Install the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install" for the machine that is being serviced.
- Install the drawbar (if equipped). Refer to Disassembly and Assembly, "Drawbar - Remove and Install" for the machine that is being serviced.
Caterpillar Information System:
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Connect
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Remove
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Install
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Disassemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Assemble
D5M Track-Type TractorPower Train Transmission - Disassemble
D5M Track-Type TractorPower Train Transmission - Assemble
D5M Track-Type TractorPower Train Track Roller Frame - Remove
D5M Track-Type TractorPower Train Track Roller Frame - Install
D5M Track-Type TractorPower Train Track Roller - Remove
D5M Track-Type TractorPower Train Track Roller - Install
D5M Track-Type TractorPower Train Track Roller - Disassemble
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Remove
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Separate
3406C Engines for Caterpillar Built Machines Cylinder Head
966G and 972G Wheel Loaders Radiator Core - Clean
D5M Track-Type TractorPower Train Bevel and Transfer Gears - Assemble
D5M Track-Type TractorPower Train Bevel and Transfer Gears - Disassemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Cab - Install
515 Wheel Skidder and 525 Wheel Skidder Window Wiper - Inspect/Replace
623F Wheel Tractor-Scraper Power Train Machine Preparation for Troubleshooting
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Truck Payload System (TPS) General Information
615C Series II Wheel Tractor-Scraper Machine Systems Brake Control Valve (Service) - Remove and Install
615C Series II Wheel Tractor-Scraper Machine Systems Carry-Check Valve - Remove and Install