Track Roller Frame - Install
Installation Procedure
Show/hide table
Required Tools     | A     | B     | C     | D     |
---|---|---|---|---|
1P-1839 Bearing Puller Adapter     | 1     |     |     |     |
5P-8713 Plate     | 1     |     |     |     |
8S-5559 Screw     | 1     |     |     |     |
8S-6587 Adapter     | 1     |     |     |     |
5F-7353 Washer     | 1     |     |     |     |
2J-3507 Full Nut     | 1     |     |     |     |
9U-6600 Hand Hydraulic Pump     | 1     |     |     |     |
1P-1836 Pulling Adapter     |     | 1     |     |     |
8S-7610 Base     |     |     | 2     |     |
8S-7650 Cylinder     |     |     | 2     |     |
8S-7640 Stand     |     |     |     | 4     |
8S-7611 Tube     |     |     |     | 4     |
8S-7615 Pin     |     |     |     | 4     |
Show/hide table
Personal injury or death can result from falling track. Separating a track can cause the track to fall too fast. Before doing any service work which requires separating a track, a thorough inspection of the front track roller frame must be made. The tractor must be on a hard, level surface before the track roller frame is removed. See Special Instruction SMHS8273 for further information. |
- Install seal (2) on pivot shaft (1). Install the seal so that the larger diameter is toward the outside of the machine.
Show/hide table
Illustration 1 | g00557303 |
- If the bearings were removed from the track roller frame, lower the temperature of the bearings.
Show/hide table
Illustration 2 | g00677649 |
Show/hide table
Illustration 3 | g00557327 |
- Install inside bearing (3) by using Tooling (A) until the bearing is seated in the track roller frame. The inside diameter must be 88.744 ± 0.084 mm (3.4939 ± 0.0033 inch) after installation.
- Install outside bearing (4) by using Tooling (B) until the bearing is seated in the track roller frame. The inside diameter of the bearing must be 69.856 ± 0.134 mm (2.7502 ± 0.0053 inch).
- Fasten a hoist to track roller frame (6), as shown. Put the track roller frame in position on the pivot shaft. Install retainer (5) and the bolts in order to hold the track roller frame in place on the pivot shaft.
Show/hide table
Illustration 4 | g00557329 |
- Align the track roller frame with the equalizer bar. Install pin assembly (7) .
Show/hide table
Illustration 5 | g00557330 |
- Install bolt (8) in order to hold pin assembly (7) in position.
- Remove the shims at location (X) between the equalizer bar and the main frame.
- Install O-Ring seal (10) on retainer (9). Put clean oil on the O-Ring seal.
Show/hide table
Illustration 6 | g00557599 |
- Install retainer (9) on the track roller frame.
Show/hide table
Illustration 7 | g00557602 |
- Lift the machine from Tooling (D) by using Tooling (C). Remove Tooling (D) and lower the machine to the ground.
Show/hide table
Illustration 8 | g00557604 |
- Fill the pivot shaft compartment with oil to the correct level. See the Maintenance Guide.
End By: Connect the tracks. Refer to Disassembly and Assembly, "Tracks - Connect" for the machine that is being serviced.
Caterpillar Information System:
D5M Track-Type TractorPower Train Track Roller - Remove
D5M Track-Type TractorPower Train Track Roller - Install
D5M Track-Type TractorPower Train Track Roller - Disassemble
D5M Track-Type TractorPower Train Track Roller - Assemble
D5M Track-Type TractorPower Train Track Carrier Roller - Remove
D5M Track-Type TractorPower Train Track Carrier Roller - Install
D5M Track-Type TractorPower Train Track Carrier Roller - Disassemble
D5M Track-Type TractorPower Train Track Carrier Roller - Assemble
D5M Track-Type TractorPower Train Track Adjuster - Remove and Install
D5M Track-Type TractorPower Train Track - Separate
D5M Track-Type TractorPower Train Track - Disassemble
D5M Track-Type TractorPower Train Track - Connect
D5M Track-Type TractorPower Train Track Roller Frame - Remove
D5M Track-Type TractorPower Train Transmission - Assemble
D5M Track-Type TractorPower Train Transmission - Disassemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Assemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Disassemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Install
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Remove
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Connect
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Install
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Remove
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Separate
3406C Engines for Caterpillar Built Machines Cylinder Head