Hydraulic Electronic Control - Remove and Install
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Note: Put identification marks on all wires for installation purposes.
- Lower the bucket to the ground.
- Remove screw (1) and three screws (3) .
Show/hide table
Illustration 1 | g00445184 |
- Disconnect switch assembly (2) .
- Remove cover (4) .
- Remove three screws (5) and cover (6) .
Show/hide table
Illustration 2 | g00445185 |
- Remove bolts (7) and bolts (8) .
Show/hide table
Illustration 3 | g00445187 |
Show/hide table
Illustration 4 | g00445188 |
Rear View |
- Remove the cover enough to disconnect cigar lighter (9) .
- Remove cover (10) .
- Disconnect electrical connectors (13) .
Show/hide table
Illustration 5 | g00445189 |
- Remove bolts (11) and hydraulic electronic control (12) .
- Remove two nuts (14), the washers, and electronic position control (15) .
Show/hide table
Illustration 6 | g00445365 |
Installation Procedure
- Install electronic position control (15) .
Show/hide table
Illustration 7 | g00445365 |
Note: The slot in the electronic position control must be aligned to the slot of the control assembly.
- Apply 9S-3263 Thread Lock Compound to the threads of the threaded rods.
- Install the washers and nuts (14). The torque for nuts (14) is 2.25 ± .25 N·m (20 ± 2 lb in).
- Install hydraulic electronic control (12) and bolts (11) .
Show/hide table
Illustration 8 | g00445189 |
- Connect electrical connectors (13) .
- Install cover (10) .
Show/hide table
Illustration 9 | g00445187 |
Show/hide table
Illustration 10 | g00445188 |
- Connect cigar lighter (9) .
- Install bolts (8) and bolts (7) .
- Install cover (6) and three screws (5) .
Show/hide table
Illustration 11 | g00445185 |
- Install cover (4) .
Show/hide table
Illustration 12 | g00445184 |
- Connect switch assembly (2) .
- Install three screws (3) and screw (1). The torque for screw (1) is 6 ± 1 N·m (53 ± 9 lb in).
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
631E Series II Wheel Tractor-Scrapers Seat Suspension - Lubricate
928G Wheel Loader Lubricant Viscosities
623F Wheel Tractor-Scraper Hydraulic System Pressure and Flow Compensator Valve
D8R Track-Type Tractor Walk-Around Inspection
994D Wheel Loader Axle Oscillation Bearings - Lubricate
623F Wheel Tractor-Scraper Hydraulic System Piston Pump (Elevator)
928G Wheel Loader Sampling Interval and Location of Sampling Valve
928G Wheel Loader Tire Shipping Pressure
D8R Track-Type Tractor Tracks
631E Series II Wheel Tractor-Scrapers Router Bits - Inspect/Replace
627F Wheel Tractor-Scraper Rollover Protective Structure (ROPS) - Inspect
613C Series II Wheel Tractor-Scraper Machine Systems Ejector Support Roller - Assemble
D8R Track-Type Tractor Leaving the Machine
994D Wheel Loader Braking System Check Valve (Brake Oil Cooler Bypass)
627F Wheel Tractor-Scraper Window Washer Reservoir - Fill
928G Wheel Loader Circuit Breakers and Fuses - Reset/Replace
994D Wheel Loader Braking System Pressure Switch (Steering and Brake Filter)
631E Series II Wheel Tractor-Scrapers Window Wiper - Inspect/Replace
D7R Track-Type Tractor Power Train Steering Differential and Brakes
D7R Track-Type Tractor Power Train Brake Control Valve
631E Series II Wheel Tractor-Scrapers Wheel Bearing Oil - Change
994D Wheel Loader Braking System Brake Control (Parking Brake)
966G and 972G Wheel Loaders Power Train Tire and Rim (Front) - Remove and Install
D7R Track-Type Tractor Power Train Equalizer Bar